5.CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVERS
Follow the instructions below if you want to change the operation code.
1 Pry off the battery cover of the trans- mitter with a coin, as shown.
BATTERY
2 You will see 9 connectors labeled from “1” to “9”, as shown. (the connectors setting may not be the same as shown.)
You can randomly remove some connectors, leaving some in place. A connector can be removed with the clip, as shown.
3If the connector is placed on the top and middle posts, that column is
set on “ + ” . If the connector is placed on the middle andbottom posts,
that column is set on “ - ”. If the connector is removed completely, (not | ||
placed on any posts), it is set to “ 0 ”. (see | ‘0’ | |
diagram for examples of how to set a | ||
| ||
column to the three different positions). |
| |
When removing a connector to set a | ‘+’ | |
column to “ 0 ”, save the connector in | ||
case you change the code at a later date.
4After setting up the code connectors on the transmitter, you are ready to set the same code on the receivers.
| Remove the receiver from the electrical outlet before |
WARNING | changing the code. |
|
5 On the garage door receiver and wireless switch receiver, remove the screw that holds the connector covers, and remove the covers.
6You will see 10 connectors. For connectors “1” to “9”, the settings
must match with those of the transmitter.
Connectors
1 to 9 are
the same. | BATTERY |
7Connector 10 on the receiver should be set to “+” if it is controlled by the transmitter’s left button , connector 10 on the receiver should be removed if it is controlled by the transmitter’s right button. Example, if the left button is used to control the garage door receiver, connector 10 on the garage door receiver should be set to ”+”. If the right button is used to control the wireless switch receiver, connector 10 on the wireless switch receiver should be removed.
Connector 10 set to “+” | TRANSMITTER | |
Connector 10 “Removed” | ||
| ||
GARAGE DOOR RECEIVER | WIRELESS SWITCH RECEIVER | |
318R |
8Put the cover and screw back onto the receivers. Install the garage door receiver and wireless switch receicer based on previous illustrations on sections 2 and 4.
9Put the battery cover back onto the transmitter.
10Press the left button on the transmitter to operate the garage door receiver orpressthe right button to turn on/off the light fixture/small appliance.
6. BATTERY
12 volt alkaline battery (size 23A) (included).
It is time to change the battery when the red LED on the trans- mitter does not turn on when either button is pressed.
7. ADDITIONAL TRANSMITTER
You can add as many additional transmitters as you want to control the same receiver. Simply set the same operation code on all transmitters with the same code setting on the receiver. Skylink® offers Keychain Transmitter Model 318TN to work with your receiver. For more information, please visit our website at www.skylinkhome.com or contact us.
8. CAUTION
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION:NOTFORUSEWITHDIMMER.
CAUTION:DISCONNECTPOWERBEFORECODECHANGING. REPLACE COVER AFTER CODE CHANGING.
MODEL:318R
Maximum Rating:
Input : 120VAC 60Hz 2W
Maximum Rating :
Input : 120VAC 60Hz
Resistive load : 8A (960W)
Incandescent : 300 watts
Motor Load : 1/3 HP
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferencebyoneormore of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
10. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
11.CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work, please :
1.visit our FAQ website at www.skylinkhome.com, or
2.email us at support@skylinkhome.com, or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N.
USPatent.D380895
©2005 SKYLINK GROUP
