Universal Garage Door

 

Keypad Control

Model GBRK

1. INTRODUCTION

 

 

 

Congratulations on your purchase of the Skylink® GBRK Universal Garage Door Keypad Control. This is a kit with a universal keypad transmitter and Smart ButtonTM. In this kit, you will find the following:

Mounting

 

 

Accessories

Garage Door

Crimper

 

 

 

Receiver

 

Keypad Transmitter

Smart ButtonTM

 

(Battery included)

GB-318

Double Sided Tape

 

2. RECEIVER INSTALLATION

 

 

 

Unplug the power cord of your garage door opener before installation to ensure

 

power is not connected.

WARNING

DO NOT let children use the gargae door Transmitter without adult supervisor.

Children can injure themselves or others by the garage door.

DO NOT use remote to control the door without safety beams.

2.RECEIVER INSTALLATION (CONT)

5.If the wall button wires are hidden inside the

wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door

opener.

6.Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes.

If the Smart ButtonTM GB-318’s red LED does not flash after the Antenna Smart ButtonTM GB-318 has been connected to the wall button’s

wires for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM GB-318 will still work if you plug in an adapter (purchased separately). Please

contact Skylink® to purchase the adapter.

1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console.

2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.

Wall Button

Ribbon Wires

NOTE:

Ensure the ribbon wires are not twisted but laid flat inside the clip.

Easy ClipTM

Rating of the transformer:

12V DC, 100mA Diameter of DC plug : 3.5mm

7. Secure the Smart ButtonTM GB-318 properly with the mounting accessories.

Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.

Note: After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it.

3. PROGRAM KETPAD TRANSMITTER G6K TO RECEIVER GB-318

You need to do the programming in order to add the transmitter to a receiver.

If your wall button ribbon wires are not the same kind as shown in the diagram, please refer below (4) or visit our website www.skylinkhome.com or contact us for more information.

3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.

Press / lock

Ribbon Wires

Smart ButtonTM GB-318 can learn up to 10 remote controls.

To add remote controls, follow the instructions below:

1.Press the learn button on the side of the Smart ButtonTM GB-318.

2.Once the learn button is pressed, the LED will flash quickly. Release the learn button.

3.Enter [PIN][#][assigned number of door] on the keypad transmitter you would like to program.

The assigned door number can be either

LED

1, 2, 3, or 4.

 

4. Once the keypad transmitter is programmed, the

Learn

LED will flash slowly, in the same way as it

flashes in standby mode.

Button

 

5. You may now operate the garage door opener

Smart ButtonTM GB-318

with this new keypad transmitter.

 

4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button.

a) Disconnect the existing wall button from the wall.

b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM GB-318 and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal.

c) Reconnect the wall button back.

4. OPERATION

If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

 

LED

Press the programmed button on the remote control

 

or Smart ButtonTM GB-318, it will open / close the

OPEN /

garage door.

CLOSE

Button

 

Note: After connecting this NEW Remote Control to your wall button, your existing remote control will still work with this connection.

Page 1
Image 1
SkyLink GBRK manual Introduction, Receiver Installation, Program Ketpad Transmitter G6K to Receiver GB-318, Operation

GBRK specifications

SkyLink GBRK is an innovative satellite communication system designed to enhance global connectivity and data transmission. Developed by a consortium of leading aerospace and telecommunications companies, SkyLink GBRK integrates cutting-edge technologies to facilitate high-speed internet access, enhance broadcasting, and support critical communications in remote areas.

One of the main features of SkyLink GBRK is its utilization of low Earth orbit (LEO) satellites. These satellites operate at altitudes ranging from 500 to 2,000 kilometers, which significantly reduces latency compared to traditional geostationary satellites. The reduced latency is particularly beneficial for applications requiring real-time data transfer, such as video conferencing, online gaming, and financial transactions.

SkyLink GBRK employs advanced frequency bands, including Ka-band and Ku-band, to optimize data transmission rates and improve communication reliability. The Ka-band allows for higher bandwidth availability, supporting HD video streaming and large file transfers, while the Ku-band provides robust connectivity in adverse weather conditions. This combination ensures that users experience minimal disruption during severe weather events.

The system incorporates seamless integration with terrestrial networks, enabling users to access satellite services through existing internet infrastructure. This hybrid approach enhances scalability and allows for flexible deployment, especially in rural and underserved regions where traditional broadband options may be limited.

SkyLink GBRK also prioritizes security and encryption in its communications protocols. By leveraging advanced encryption techniques, the system ensures that data transmitted between users and ground stations remains secure from unauthorized access and cyber threats. This feature is critical for businesses and organizations that rely on secure communications and data integrity.

Moreover, the user interface of SkyLink GBRK is designed for simplicity and accessibility. It offers a seamless user experience across devices, including smartphones, tablets, and laptops. With easy navigation and setup, users can connect to the satellite network effortlessly.

In summary, SkyLink GBRK stands out as a robust satellite communication solution that combines advanced satellite technology, reliable connectivity, and user-friendly design. Its ability to support high-speed data transmission in diverse environments makes it an essential tool for bridging the digital divide and empowering users worldwide.