4. OPERATION (CONT)
The keypad transmitter can operate up to 4 Smart ButtonTM units, that also means one keypad transmitter can operate up to 4 garage door openers. Same PIN will be used for all doors. The factory default password is [0 0 0 0].
To operate door 1, you will enter [0 0 0 0][#][1]
To operate door 2, you will enter [0 0 0 0][#][2]
To operate door 3, you will enter [0 0 0 0][#][3]
To operate door 4, you will enter [0 0 0 0][#][4]
To program the keypad transmitter into the Smart ButtonTM, you must decide which door you need to operate. If you only have one Smart ButtonTM, we suggest you to use door 1. i.e. [0 0 0 0][#][1].
If you do not hear 3 beeps after entering the PIN, i.e. [0 0 0 0][#][1], that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door.
Follow the instructions below to change the PIN.
To change your PIN:
1.Enter the current PIN, (factory default PIN 0 0 0 0), press * .
2.Enter new 4 to 6 digit PIN, press * .
3.Enter new PIN again, press * .
For example, if you are changing the PIN number from 0000 to 123456, enter the following sequence, 0000, *, 123456, * , 123456, * .
If confirmed, the backlit LED flashes and the unit emits a long beep.
5. ERASE TRANSMITTERS
To erase unwanted remote control(s) from the memory of Smart ButtonTM
1.Press and hold the learn button for approximate 10 seconds.
2.The LED will flash rapidly after 10 seconds to indicate all the pro- grammed remote controls have been erased. You may now release the learn button.
3.You have erased all the remote controls programmed to the Smart ButtonTM
6.TROUBLE SHOOTING
Q:What can I do if the door opener does not react after I press the button on the transmitter ?
A:- Ensure when the button on the transmitter is pressed, the red LED on the transmitter comes on. Otherwise, check if the battery is inserted properly.
-Make sure the correct button on the transmitter is pressed.
-Ensure the wires that were previously connected to the wall mounted door control are not loose.
-Ensure the transmitter has been programmed to the receiver. Refer to section 3 for how to program a transmitter to the receiver.
7. BATTERY
Two 3 volt Lithium type (CR2032) batteries (included).
-
Battery
Compartment
+
It is time to change the batteries when the backlight no longer appears.
8. ADDITIONAL TRANSMITTER
You can add up to 10 additional transmitters to control the same receiver. Skylink® offers Keychain Transmitters and Visor Transmitters to work with your receiver. For more information,
please visit our website at www.skylinkhome.com or contact us.
9. WARNING
DO NOT let children use the garage door transmitter without adult supervision. Children can injure themselves or others by the garage door.
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
11. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
12. CUSTOMER SERVICE
If you would like to
-find out the
-know more about features and applications
-download documents, i.e. user’s instructions
-order Skylink products
or if you have difficulty getting products to work, please:
1.visit our FAQ section at www.skylinkhome.com, or
2.email us at support@skylinkhome.com, or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N.
Patent pending
®are registered trademarks of their respective corporations ©2010 SKYLINK GROUP
