SkyLink GM-434TL manual Introduction, Programming Cont, Erasing a sensor, Installation

Garage Door
MonitorTM Sensor	Model GM-434TL

1. INTRODUCTION

The Garage Door MonitorTM Sensor is designed to monitor the status of

your garage door and advise you if the door is open. When the garage door is open, receiver will flash along with alert beeping or alarm.

In this package, you should find a Garage Door MonitorTM Sensor, 3V lithium battery (installed) and other mounting accessories.

Mounting

Accessories

Garage Door

MonitorTM Sensor

Please follow the instructions below to set up your garage door monitorTM sensor.

2. PROGRAMMING

The sensor must be programmed to the Household Alert® Long Range Receiver before they can communication. You may program the sensor to one of the 4 zones. Follow the instructions below;

1.Plug in an AC adapter to the receiver.

2.Power up the Receiver unit. The green LED will be on indicating it is turn on.

3.Open the back cover and there is a learn button. Press and hold this learn button for 5 seconds, until both green LED and zone 1 red LED flash. You may now release the learn button.

4.If you would like to program the sensor to zone 1, activate the sensor while the zone 1 red LED is flashing. Activate the Sensor by position the sensor vertically to allow the detection rod to drop.

5.If you would like to program the sensor to other zones, press the learn button again, until the red LED flashes at the zone you want to program the sensor to, then activate the sensor.

6.Once the sensor is programmed, the green LED will be steadily on and none of the red zone LEDs will be on.

Plug in the adapter to the receiver

2.PROGRAMMING (CONT)

1)Zone LED of this sensor will flash.

2)Beeping according to the zone number [Operating mode is set to “Alert”]. 1 beep for zone 1, 2 beeps for zone 2 and etc, until the detection rod is retracted.

Erasing a sensor

You cannot erase a specific sensor. You must erase all sensors from the receiver, then program the ones you would like to keep. To erase all the sensors from the receiver:

1.Remove the adapter from the receiver.

2.Open the back cover, press and hold the learn button. Do not release the learn button until step 4.

3.While holding onto the learn button, plug in the adapter to the receiver.

4.You may release the learn button when the LEDs on the receiver are on.

5.You have erased all sensors from the receiver.

3.INSTALLATION

	Unplug the power cord of your garage door opener
WARNING	before installation to ensure power is not connected.

Step 1 – Select a spot on your garage door to mount the sensor

Before you install the sensor onto the garage door, make sure the garage door is closed. The sensor assembly should be mounted on one of the vertical supports of your garage door near the bottom.

When the door is closed, the detection rod should be retracted. When the door is open, the detection rod will be extended.

One of

Vertical

Supports

Door closed Door open

Detection rod is fully extended

Learn Button

Note: Each zone can program up to 4 sensors. If you try to program a fifth sensor into a zone, the first programmed sensor will be erased.

Test Sensor

After learning the sensor to the Receiver unit, you may test the communication by pushing the detection rod on the sensor to its fully retracted position. If program the sensor to Zone 1, position the sensor

Step 2 – Mount the sensor onto your garage door

You can mount the sensor onto your garage door with double-sided foam tape if the sur- face of your garage door is smooth and clean enough to provide a good adhesive surface, such surface can usually be found on a metal garage door. Please ensure the surface is smooth and clean. Important: The bottom of the sensor should be 1/2 inch above the ground. (Refer to Diagram A)

For wooden garage doors, it is recommended
to mount the sensor with screws onto the	4Screws
garage door with 3 x 18 screws provided.

Double-sided foam tape

vertically to allow the detection rod to drop while the receiver’s Zone 1 LED is flashing and the receiver will emit the beeping.

When the detection rod is	When the detection rod is
fully retracted, the receiver	fully extened, the receiver
will not beep.	will beep and zone LED will
	flash.

Note:

When the garage door is opening/closing, make sure the sensor does not interfere with the safety reversing sensor or safety beam sensor supplied with your existing garage door opener.

Note: Ensure you straighten up the antenna	1/2 Inch
on the receiver to receive the best possible		Diagram A
reception.