SkyLink Model UR-100 Programming the Skylink Model #88, #88C, Warranty, Garage Door, Gate Opener

Frequency Switch

PROGRAMMING THE SKYLINK MODEL #38, #38C

PROGRAMMING THE SKYLINK MODEL #68, #68C, #68B, #68G, #68R

6.To move the connectors, slide an opened paper clip into the side of a connector and lift. (see diagram M) When repositioning connec- tors, place a connector on the two chosen posts, then push down on the connector with your finger.

Paper

Clip

7.Set the connectors num- bered 1 through 9 so that the switches on the trans- mitter match those on the receiver. Leave the re- maining posts at “ 0 ”,or the blank position (remove the connectors). See the diagram J for details.

8.Test the transmitter with the Universal receiver.

1.Locate frequency switch on the top of the trans- mitter and set to position A. (See diagram N)

Diagram N

2. To program the model	3. The transmitter has 12 rows
#68, #68C, #68B, #68G,	of posts, each row has 3
#68R, open the case	posts. (see diagram P)
with a coin. (See dia-
gram O)

Diagram O

4.Use an opened paper clip to set the connectors numbered 1 through 9 so that the switches on the transmitter match those on the receiver. To operate with Skylink #UR100, only set to “ + ” or “ 0 ” position. Do not place the connector to the middle & bottom posts “ -position”. Leave the remaining posts at “ 0 ”, orthe blank position (remove the connectors). See the Diagram J for details.

5.Test the transmitter with the Universal receiver.

Diagram M

Diagram P

PROGRAMMING THE SKYLINK MODEL #88, #88C

PROGRAMMING THE SKYLINK MODEL #88p

1.To Program Your Keypad

-Open the cover on the back. (See diagram Q)

CLOSE

2.Set brand jumper by moving the red plastic tab to the number 7 jumper. Slide an opened

paper clip into the	Frequency
top of the red plastic	Switch
tab, then lift and re-
position.

4. Use a pen or paper clip

to set the corresponding

DIP switches numbered

1 through 9 so that the

switches on the trans-

mitter match those on

the receiver. Each switch

the transmitter at “0” or the center position. (See diagram S)

DIP Switch

Location

1.To Program Your Keypad

-Open the cover on the back. (See diagram T)

CLOSE

2.Set brand jumper by moving the red plastic tab to the number 7 jumper. Slide an opened

paper clip into the top of the red plastic tab, then lift and re- position.

OPEN

Diagram Q

3. Set the frequency
switch located above
to “ D ” position (slide	DIP Switch Location
the switch as far
right as possible).
(See diagram R)
	1	2	3	4	5	6	7	8
		Brand Jumper

Diagram R

of the transmitter has 3

positions (“ + ”, “ 0 ”,

“ - ”). To operate with

Skylink #UR-100, only

set the switches to “ + ”

or “ 0 ”. Do not use “ - ”

position. Leave the re-

maining DIP switches in

Diagram S

5.Refer to the keypad manual to test the transmitter with the Universal receiver.

OPEN

Diagram T

3.Set the frequency switch located above to “ D ” position (slide the switch as far right as possible). (See diagram U)

Code connector Location

1 2 3 4 5 6 7 8

Brand Jumper

Diagram U

PROGRAMMING THE SKYLINK MODEL #88p

WARNING

WARRANTY

FCC

Skylink will not be held liable	®
or responsible for

4.The connector (See diagram V) has 12 rows of posts, each row has 3 posts. Each row contains one connector (See diagram W). Set the code connectors from number 1 through 9 so that the switches on the transmitter match those on the receiver.

To operate with #UR100, only set the connectors to “ + ” or “0” (blank position). Do not set the connectors to “ - ” position. Leave the remaining posts at “ 0 ”, or the blank position (remove the connectors). See the diagram L for details.

Diagram V

Diagram W

5.Refer to the keypad manual to test the transmitter with the Universal receiver.

DO NOT let children use any garage door transmitter without adult supervision. Children can injure themselves or others by the garage door.

If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase is required.

The Universal Garage Door Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions :

1.This device may not cause harmful inter- ference.

2.This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party res- ponsible of compliance could void the user’s authority to operate the equipment.

any misuse or application		GARAGE DOOR/
of this product other than
	corporations	GATE OPENER
for its intended use.
		UNIVERSAL RECEIVER
SKYLINK		USER'S INSTRUCTIONS
	respective
TECHNOLOGIES INC.		(Model UR-100)
2213 Dunwin Drive,
Mississauga, Ontario
	their
L5L 1X1, CANADA
	of
(905)608-9223
	trademarks
(905)608-8744 FAX
Email:support@skylinkhome.com
(Reply within 24 hrs)
Customer Service : (800)304-1187	registered
http://www.skylinkhome.com
P/N. 101A111-003 Rev.3
Patent no. 382251	® are
Patents Pending
©1999 SKYLINK TECHNOLOGIES INC.