4. PROGRAM A TRANSMITTER TO THE RECEIVER
You need to do the programming in order to add a transmitter to the receiver.
Button B
| Button A |
| |
| Model 18TN |
| |
Learn | Button A | Button B | |
Button D | |||
Button | |||
Button C | |||
|
|
Model 18T4
1Plug the receiver into an electrical socket.
2Depending on what application you would like to control, the programming sequence is slightly different.
Program a transmitter to operate garage door opener:
Press the learn button once to program a transmitter to operate the garage door opener, the LED will flash slowly indicating the transmitter (button) you are about to program will control the garage door opener.
Program a transmitter to operate lighting control:
Press the learn button again (twice) to program a transmitter to operate the lighting control, the LED will flash rapidly indicating the transmitter (button) you are about to program will control the lighting.
3Press the assigned button of transmitter 18TN (either button A or B) or trans- mitter 18T4 (either button A, B, C or D) you want to program to the receiver.
4The receiver red LED will stop flashing indicating the programming is completed.
5Repeat steps 1 to 4 to program addition transmitter (button).
5. REMOVE TRANSMITTER FROM THE RECEIVER
You can delete the transmitter from a receiver by following the instructions below:
1Unplug the receiver from the electrical socket.
2Press and hold the learn button on the left hand side of the receiver when plugging the receiver into an electrical socket, the red LED on the receiver will flash rapidly. All the transmitters and keypads are deleted.
6. ADDITIONAL TRANSMITTER
You can add up to 15 transmitters as you want to control the same receiver. Simply program the transmitters to the receiver. Skylink® offers Keychain Transmitter Model 18T4 and Keyless Entry Transmitter Model 18K to work with your receiver. For more information, please visit our website at www.skylinkhome.com or contact us.
7. TROUBLE SHOOTING
General
Q:The programmed transmitter (button) should operate the garage door, but now it turns on the light, or vice versa.
A:You have programmed the transmitter to the receiver incorrectly. Please erase the programmed transmitter(s) from the receiver, and then
Q: Receiver does not react after pressing the button on the transmitter ?
A:- Ensure when the button on the transmitter is pressed, the red light on the transmitter comes on. Otherwise, check if the battery is inserted properly.
-The appropriate button on the transmitter should be pressed.
-Ensure the transmitter has been programmed to the receiver. Refer to section 4 for how to program a transmitter to the receiver.
7. TROUBLE SHOOTING (CONT)
Garage Door Opener
Q: Door opener does not react after pressing the button on the transmitter ?
A:- If the red light on the receiver flashes when you press the appropriate button on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control.
-Ensure the wires that are previously connected to the wall mounted door control are not loose.
Lighting
Q:After pressing the button on the transmitter, I hear a “click” sound from the receiver, but the plugged in lighting is not on.
A:Please ensure the power cord of the plugged in light is securely plugged into the receiver. Also, if the plugged in light has a on/off switch, that switch must be turned on.
8. CAUTION
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION : DISCONNECT POWER BEFORE SERVICING.
Maximum Rating:
Input : 120VAC 60Hz
AC socket for appliance control
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION : NOT FOR USE WITH DIMMER.
DISCONNECT POWER BEFORE SERVICING.
Maximum Rating :
Incandescent : 300 watts
Motor Load : 1/3 HP
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
10. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
11. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work, please :
1.visit our FAQ website at www.skylinkhome.com, or
2.email us at support@skylinkhome.com (reply within 24 hrs), or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N. 101A402
©2005 SKYLINK GROUP
