Safety Information
Section 1 - Setting up the Wall Switch Receiver
Section 2 - Setting up the Wireless Wall Switch Transmitter
INSTALLATION INSTRUCTIONS
WIRELESS 3 WAY ON/OFF KIT
Model: SK8
Turn o power to the circuit breaker before installing.
If you are uncertain or uncomfortable performing this installation, please consult a qualied electrician. This manual should also be kept for future reference.
For indoor use only.
DO NOT use this product to control loads over the specied maximum rating.
The device is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference that may cause undesired operation.
WARNING: Changes or modications to this unit not expressly approved by the party responsible of compliance could void the user’s atuhority to operate the equipment.
Technical Specications
Input Voltage | 120V AC, 60Hz |
|
|
Standby Current | 0.2mA |
|
|
Minimum Load | 10W |
|
|
Maximum Ballast Load | 500W |
|
|
Maximum Tungsten Load | 600W |
|
|
Maximum Resistive Load | 1000W |
|
|
Operating Frequency | 318MHz |
|
|
Operational Temperature |
WARNING: Turn o power to the circuit that you plan on installing the Wall Switch to, at the circuit breaker. Failure to turn o power at the circuit breaker can result in electrical shock, causing severe or fatal injury.
NOTE: The Wall Switch is designed to operate a maximum load of 1000W at 120VAC.
NOTE: If you already have an existing 3 Way Switch, disable one switch and replace the other switch with the Wall Switch Receiver.
1.Loosen the screws on the wallplate cover of the Wall Switch receiver and remove it before installing.
2.Install the Wall Switch with the 3 wires, Live, Load and Ground. Use the provided wire nuts (C) to connect these wires respectively to the existing wires from the wall. Neutral wire is not required and cannot be connected to the Wall Switch Receiver. Refer to Section 10 for neutral wiring.
3.After all the wires are connected, ensure that all of the wire connectors are attached securely and there should be no exposed copper wiring. Secure the Wall Switch with screws.
Ground
GreenLoad
Red
Live
Black
4.Turn the circuit breaker back on.
5.The two blue LEDs will be on. If the blue LEDs remain o, please check and ensure the light bulb is installed and in good position and that the wires are connected correctly.
6.After the Wall Switch is installed, press the Switch Button to turn the lights on and o.
Switch
Button
Blue
LEDs
INSTALLING WITH DOUBLE SIDED TAPE
NOTE: The Wireless Wall Switch Transmitter comes with a lithium battery already installed. Remove the battery isolator tag from the Wireless Wall Switch transmitter before installing.
1.First clean the wall surface where you plan to install the Wireless Wall Switch transmitter.
2.Place the two foam tapes (E) on the back of the Wireless Wall Switch transmitter plate.
3.Peel o the foam tape cover and stick it to the wall surface.
Place double-sided foam tape
Congratulations on your purchase of the SkylinkHomeTM Wireless 3 Way On/O Kit, model SK8. Simply replace your existing wall switch with the Skylink Wall Switch receiver and mount the Wireless Wall Switch Transmitter anywhere you would like to control your lighting.
Humidity | 5% - 95% |
|
|
Range | Up to 500 feet in open area |
Grey Antenna
NOTE: Do not cut the antenna.
Warranty
ONE YEAR WARRANTY
This product is guaranteed to be free of defects in materials and workmanship for
1 year from the date of purchase. If this product is defective, call
If you have any questions, problems or missing parts, please call Skylink Customer Support: 9:00am - 5:00pm EST,
Or
www.skylinkhome.com
CUSTOMER SERVICE
17 Sheard Avenue,
Brampton, Ontario,
Canada L6Y1J3
P/N : 101Y157 Rev:0 ©2014 SKYLINK GROUP.
Package Contents
AB
CD
E
Part | Description | Quantity |
|
|
|
A | Wall Switch Receiver | 1 |
|
|
|
B | Wireless Wall Switch Transmitter | 1 |
|
|
|
C | Wire Nuts | 3 |
|
|
|
D | Screws and anchors | 2 |
|
|
|
E | 2 | |
|
|
|
Section 2 - Setting up (continued)
INSTALLING WITH SCREWS
NOTE: The Wall Mount transmitter comes with a lithium battery already installed. Remove the battery isolator tag from the Wall Mount Transmitter before installing.
Installing to an Existing Wall Switch
1.Loosen the screws on the wall plate of the Wireless Wall Switch transmitter and tighten the two included screws (D) on the back plate to the existing wall box.
2.Tighten the two screws on the wall plate to the back plate to secure it.
3.The Wireless Wall Switch transmitter is now ready to be controlled.
D
Existing Wall Box (No Anchor)
Installing on New Wall Surface
1.Drill two small pilot holes based on the two mounting screw positions and insert the anchors (D) before tightening the back plate with screws (D).
2.Tighten the two screws on the wall plate to the back plate to secure it.
3.The Wireless Wall Switch transmitter is now ready to be controlled.
DD
Section 3 - Operation
Wall Switch Receiver | Wireless Wall Switch Transmitter |
1. To turn the light on press the Switch Button once and to turn it o | 1. To turn the light on and o, push the Wireless Wall Switch pad from one |
press it once more. | position to the other. |
Push
Press | Push |
|
Drill 2 pilot holes & insert anchors
