SkyLink SK8 installation instructions Snap a cover into your Skylink Wall Switch

Section 4 - Programming

NOTE: Before programming, remove the wall plate on the Wireless Wall Switch transmitter by loosening the screws.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.Press the Switch Button on the Wall Switch receiver to turn the lights on. The two blue LEDs should go o￿.

2.Press and hold the learn button for about three seconds until the upper blue LED ￿ashes quickly and then release the learn button.

Section 5 - Erasing

NOTE: All previously programmed devices will be erased. You must re-program the devices you want to keep.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1. Press the Switch Button on the Wall Switch receiver to turn the lights on.

The two blue LEDs should go o￿.

Section 6 - Enable/Disable On/O￿

NOTE: On/O￿ Mode turns the lights on/o￿.

1.	Turn the light on with the programmed transmitter or Switch Button.
2.	Press and hold the learn button on the Wall Switch receiver for about 3
	seconds until the upper blue LED ￿ashes quickly.
3.	Release the learn button.

Section 7 - Countdown Timer Mode

NOTE: If the Countdown Timer Mode is activated, the light connected to the Wall Switch receiver will ￿ash for a predetermined time interval and then turn o￿.

NOTE: You must compete the programming sequence within the 15-second interval, otherwise the Wall Switch receiver will quit from programming mode and you will need to start again from step 1.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

Section 8 - Setting a Timer Duration

NOTE: This section is for transmitters that are programmed to Countdown Timer

Mode. The timer duration can be set for the following times: 1 minute, 5 minutes, 15 minutes, 30 minutes or 60 minutes.

NOTE: Once the number of ￿ashes reaches 5, it will stay at this setting. If you would like to go back to other settings, such as 1 minute, release the button and repeat from step 1 to start over.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

Blue LEDs	Touch Plate
	Learn Button

3.Press the learn button on your Wireless Wall Switch transmitter. The red LED will be on for 15 seconds.

4.Press the pad (switch) on the Wall Switch Transmitter, the red LED will

￿ash and then go o￿. The upper blue LED on the Wall Switch Receiver will also turn o￿.

5.Both wall switches are now programmed.

CR 2032	Learn Button
+
Red
LED	Pad

2.	Transmit an “Erase” code from the transmitter until step 5. Refer to the
	user’s instructions of the transmitter on how to transmit an “Erase” code.
3.	Press and hold the learn button for about 3 seconds, until the upper blue
	LED ￿ashes.

Switch Button

Blue LEDs

Learn Button

4.Release the learn button.

5.All devices have now been successfully erased.

4. The Wall Switch receiver is now in the On/O￿ Mode.

1.To program a transmitter to operate in Countdown Timer Mode, hold the learn button on your Wall Switch receiver for about 10 seconds, until the upper blue LED is on steadily, then release the learn button.

2.Press the learn button on your transmitter. The red LED will be on for 15 seconds.

3.Once the transmitter is programmed, both blue LEDs will ￿ash quickly and stop ￿ashing.

4.The transmitter has been successfully programmed.

Blue LEDs

Learn Button

NOTE: Once you have successfully completed the programming, go to section 8 to setup the timer duration for the transmitter.

1.The connected light must be turned o￿ and the two blue LEDs should be on.

2.Press and hold the learn button for three seconds until the lower blue LED ￿ashes once. The number of ￿ashes indicates the timer duration.

Number of Flashes	Timer Duration
1	1 min.
2	5 min.
3	15 min.
4	30 min.
5	60 min.

3.Continue to hold the learn button until it reaches the desired setting. The status will change every 6 seconds; so holding the learn button for another 6 seconds the number of ￿ashes will change from 1 to 2, 2 to 3 etc.

Once a transmitter is programmed for the timer mode, activating this programmed transmitter will turn the lights on for the speci￿ed timer duration. To stop timer countdown, press a programmed button for regular mode.

NOTE: During a timer countdown if the Wall Switch receiver receives another signal for timer operation, the timer will start again and override the previous timer. This will extend the on period by another timer interval.

Section 9 - Replacing the Battery

1.Remove the wall plate from the Wireless Wall Switch transmitter by loosening the two screws.

2.Remove the existing battery by sliding it out.

3.Insert the new battery, positive side up, by sliding it in and pushing down on the battery to lock it in place.

4.When the battery is installed, the red LED on the transmitter will be on for one second.

	Push
Slide in	Down
2	20	32
+	+

Battery	CR 2032
(Positive side up)	+

Red

LED

Section 10 - The Wiring Diagram

NOTE: Wire colours may vary in the junction box.

1.Wiring Diagram without Neutral Wire

2.Wiring Diagram with Neutral Wire

Troubleshooting

Problem	Solution
Wall Switch Receiver`s	- Ensure the wires are side by side and
	held together when pushing them
LEDs and the connected
	inside the wire nuts.
load will not turn on
	- Ensure the corresponding wires are
	connected correctly. Refer to Section 10.
	- Check that the circuit breaker is turned
	on.
	- If there are white wires (neutral) in the
My switch has more than
3 wires in the wall box.	wall box, connect the white wire with a
	wire nut. Only connect the Load and
	Live wires from the wall box to the Wall
	Switch Receiver.
The Wall Switch Receiver	- This is normal. Ensure the connected
is getting warm to touch.	load does not exceed the maximum
	rating.
The range of my Wall	- Keep the antenna wire as straight as
Switch Receiver is	possible and put it directly into the dry
decreasing.	wall or via the hole in the wall box.
It takes a long time for	- Ensure the timer duration is set to the
the light to turn o￿ when	desired setting.
set to Timer Mode.	- Check that there were no other Timer
	Mode signals being received as that will
	extend the ON period by another
	interval.
Can I dim the light on	- Not with this kit. Purchase the Skylink
my Wall Switch Receiver?	Wall Dimmer (WR-001 or WR-318)
	instead of this Wall Switch Receiver.

Optional Snap-On Decorative Cover

Snap a cover into your Skylink Wall Switch!

Place the Snap-On Cover on the opening of the Wall Switch receiver for a more stylish look. Press the button on the Snap-On Cover, TM-002, to turn lights on/off. Or carry the Snap-On Remote, TM-318, with you for local control and when you are done snap it back onto the Wall Switch.

Snap-On Cover	Snap-On Remote
Model: TM-002	Model: TM-318

For more information visit www.skylinkhome.com

Accessories

Add up to eight Skylink Wireless Transmitters!

Wireless Wall Switch	Motion Sensor
Model: TB-318	Model: ID-318

Snap-On Remote	Keychain Remote	LCD Deluxe Remote
Model: TM-318	Model: LK-318	Model: TD-318

Wireless Remote Control TC-Series

TC-Series Remotes are available in 1 to 14 buttons.

For more information visit www.skylinkhome.com