4. INSTALLATION (CONT)

6. BUZZER VOLUME

9. OTHER HOUSEHOLD ALERT TM SENSORS

If the surface of the frame is flat enough, double-sided foam tape is sufficient, otherwise, it is recommended to use the mounting plate and screws as well.

After mounting the sensor, put the cover back

 

 

on with the Houselink logo in the upright

 

 

position.

Mounting plate and

Double-sided Sensor

 

screws (optional)

foam tape

Magnet

 

Magnet

Sensor

Sensor

 

5. OPERATION

You can select the buzzer volume by switching the volume switch to “HI” or “LO” position.

The buzzer can be disabled by switching to the “OFF” position.

7. MUTE

When a sensor is triggered for a long period of time, you may stop the buzzer by pressing the mute button. When another signal comes again, you can disable the buzzer for all currently activated sensors by pressing the mute button. The receiver will beep again if it receives another signal.

For instance, if you know the door / window sensor will be on for a while when another family member is cleaning the window, you may want to disable the buzzer for this sensor. Then you can press the “Mute” button after it starts to sound. If any other sensor is triggered, the receiver will sound again.

The Houselink® receiver can work with up to 4 different sensors: garage door monitor sensors, door / window sensors, water sensors, indoor/ outdoor motion sensors, etc. Please visit www.skylinkhome.com or contact us at support@skylinkhome.com for more information of how to fully utilize your Door/Window Alert.

11. WARRANTY

When the magnetic contact is broken, such as when the door or window is open, the sensor will send a signal to the receiver, and the receiver will beep and the corre- sponding zone red LED will flash.

If the sensor is set to zone 1, zone 1 red LED on the receiver will flash, and the receiver will emit a continuous “single beep”, i.e. “beep” pause, “beep”, pause….. etc.

If the sensor is set to zone 4, zone 4 red LED will flash, and the receiver will emit a con- tinuous “4 beeps”, i.e. “beep beep beep beep” pause “beep beep beep beep” pause ……etc.

By the number of beeps emitted by the receiver, user can identify which zone is triggered.

8. LOSS OF SIGNAL INDICATION

When the battery level on the sensor drops to a certain level, or the sensor is out of the operating range, the receiver will show a “loss of signal” indication. The red LED representing that zone will flash rapidly, i.e. if zone 1 sensor is lost, the zone 1 red LED will flash rapidly.

When the loss of signal indication occurs, move the receiver closer to the corresponding sensor and trigger that sensor. If the red LED stops flashing rapidly, that means the receiver or sensor needs to be relocated. If the “loss of signal” indication persists, replace the battery of that sensor.

If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.

12. CUSTOMER SERVICE

If you would like to order Skylink’s products or have difficulty getting them to work, please :

1. visit our FAQ website at www.skylinkhome.com, or

2. email us at support@skylinkhome.com (reply within 24

hrs), or

3. call our toll free at 1-800-304-1187 from Monday to

10.FCC

Friday, 9 am to 5 pm EST.

Fax +800 286-1320

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CUSTOMER SERVICE

Email:support@skylinkhome.com (Reply within 24 hrs) http://www.skylinkhome.com

P/N. 101A210-001 Rev.1 ©2003 SKYLINK GROUP

Page 2
Image 2
SkyLink WD-318 Installation Buzzer Volume Other Household Alert TM Sensors, Operation, Mute, Warranty, Customer Service

WD-318 specifications

SkyLink WD-318 is an innovative wireless doorbell system that has captured the attention of homeowners seeking a reliable and advanced solution for smart entry notifications. This cutting-edge device combines elegant design with state-of-the-art technology, ensuring that users never miss a visitor again.

One of the key features of the SkyLink WD-318 is its wireless design, which allows for easy installation without the need for complex wiring or drilling. The doorbell unit is powered by batteries, making it highly versatile for different types of home layouts. The receiver plugs into a standard electrical outlet, providing flexibility in placement around the home.

The device boasts an impressive range of up to 500 feet, making it suitable for larger properties. This extensive range ensures that the chime can be heard clearly from anywhere within the house, providing peace of mind even for those working in garages or far from the front entrance.

SkyLink WD-318 offers multiple chime settings, allowing users to choose from a variety of melodies to personalize their experience. With 36 different chime options, homeowners can pick a sound that suits their style and preference, ensuring a unique notification for each visitor. The adjustable volume control feature also allows users to set the chime sound to a desired level, providing convenience for various environments.

Another significant technology that makes the SkyLink WD-318 stand out is its advanced security features. The doorbell is equipped with rolling code technology that enhances safety by changing the access code with each use. This feature helps to prevent signal interference and unauthorized access, giving users greater confidence in their home security.

The device is also weather-resistant, ensuring durability against various outdoor elements. The sleek design and sturdy construction mean that it can withstand rain, snow, and sunlight, making it an ideal choice for outdoor installation.

In conclusion, the SkyLink WD-318 wireless doorbell system offers a perfect blend of style, functionality, and security. With features such as easy installation, extensive range, customizable chimes, volume control, rolling code technology, and robust weather resistance, it stands as a leading choice for homeowners looking to enhance their property’s entryway. This innovative device promises to make welcoming guests both convenient and enjoyable.