3.PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS (CONT)
4.Within 15 seconds, follow steps A) to C).
A). Press the PROG button on the back of the TC transmitter with a sharp object.
B). Press the button on the TC transmitter that you would like to program. C). Once the transmitter is programmed, the two blue LEDs on the Wall
Dimmer flash quickly then stop flashing, indicating you have successfully programmed the transmitter to the module. Now the programmed transmitter button is ready to be used for Countdown Timer Mode.
To program other transmitters/sensors, please refer to the instructions of those transmitters/sensors and above instructions.
Note: You must complete the programming sequence within the 15-second interval, otherwise, the Wall Dimmer will quit from programming mode and you need to start again from step 1.
4. SET TIMER DURATION
As mentioned, the timer can be set to the following durations, 1 minute, 5 minutes, 15 minutes, 30 minutes, or 60 minutes.
This timer duration is used for both under Flashing Alert Operating Mode and Countdown Timer Operating Mode.
There is only one timer setting, so all transmitters that are programmed for timer mode and flashing mode will have the same timer duration. To set the timer duration, follow the instructions below:
1.Wall Dimmer must be installed and powered properly. The connected light should be off, and the 2 blue LEDs are on. The light must
be off in order to set the timer duration.
2.Press and hold the SET button for 3 seconds, the lower blue LED flashes once. The number of flashes indicates the timer duration:
Number of Flashes | Timer Duration |
| |
1 | 1 min. |
| |
2 | 5 min. |
| |
3 | 15 min. |
| |
4 | 30 min. |
| |
5 | 60 min. |
| |
3.Continue to hold the SET button until it reaches the desired setting. The status will change every 6 seconds, i.e. hold the SET button for another 6 seconds, you will see the number of flashes changes from 1 to 2, 2 to 3, etc.
Note: Once the number of flashes reaches 5, it will stay at this setting. If you would like to go back to other settings, such as 1 minute, release the button and repeat from step 1 to start over.
Once a transmitter (button) is programmed for timer mode or flashing mode, activating this programmed transmitter (button) will turn on the light for the specified timer duration.
During a timer count down, if the Wall Dimmer receives another signal for timer operation, the timer will start again and overrides the previous timer, therefore, extending the On period by another timer interval.
To stop timer count down, press a programmed button for regular mode.
5. REGULAR OPERATING MODE
The Wall Dimmer can control the light in 2 different operating modes:
1)On / Off Mode - Allows operating the light either on or off, without dimming function.
2)Dimming Mode - Allows operating the light in on, off or dimming (dim / brighten). Light source must be either incandescent light or dimmable compact fluorescent light.
The factory default operating mode is On/Off mode. However, if your light is dimmable, you may change the operating mode to Dimming Mode. To change the operating modes, please follow the instructions below:
5.REGULAR OPERATING MODE (CONT)
1.Turn on the light by the programmed transmitter or touch pad.
2.Press and hold the button on the transmitter that is programmed to the Wall Dimmer for 10 seconds or touch the touch pad for 10 seconds with your finger..
3.The light will flash. If it flashes once, that means it is in On / Off Mode. If it flashes twice, that means it is in Dimming Mode.
4.Repeating step 2 above will toggle the setting between On / Off Mode and Dimming Mode.
5.1ON / OFF operation:
Use the Wall Dimmer
To turn on / off the light, simply tap the touch pad of the wall dimmer once with your finger, it will toggle the status of the light, i.e. from on to off or from off to on.
Use a Transmitter
Wall Dimmer allows on / off operation, when the programmed button is pressed, it will transmit a signal to toggle the status of the load.
For example, if a toggle signal is received when the light is off, that signal will turn on the light.
If you have a deluxe remote, you can make sure that you will actually turn on a light by pressing [ 
] first, then the programmed button. Similarly, you can make sure that you will turn off a light by pressing [ 
] first, then the programmed button.
If you have a deluxe remote and you press [ 
], all those receivers to which the remote is programmed will turn on their loads. If you press
[ 
], all those receivers to which the remote is programmed will turn off their loads.
5.2 Brightness control operation:
Besides turning on and off the light, you may also control the brightness
of the light if the light bulb is either incandescent light or dimmable compact fluorescent light.
Use the Wall Switch
Turn on the light first. Then keep touching the touch pad to change the brightness. Remove your finger from the touch pad until the desired brightness is reached. To change the brightness in the opposite way, remove your finger from the touch pad and then keep touching again, remove the finger from the touch pad until the desired brightness is reached.
Use a Transmitter
First turn on the light.
Then press and hold the programmed button on the transmitter to change the brightness. Hold the button until the desired brightness is reached, then release the button.
Press and hold the same button again on the transmitter to change the brightness again in the opposite way. When the desired brightness is reached, release the button.
Note: Press and hold for more than 10 seconds will toggle the mode between ON/OFF and Dimming.
6. FLASHING ALERT OPERATING MODE
If a transmitter or a sensor is programmed to the Wall Dimmer under the flashing alert mode, when that transmitter is activated, the light connected will flash for the predetermined timer interval. The brightness of the light can only be set under regular mode. After the timer interval, the light will be off.
Pressing a programmed button for regular mode can override flashing alert operation.
7. COUNTDOWN TIMER OPERATING MODE
If a transmitter or a sensor is programmed to the Wall Dimmer under the countdown timer mode, when that transmitter is activated, the light con- nected will be on for the predetermined timer interval. The brightness of the light can only be set under regular mode. After the timer interval, the light will be off.
Pressing a programmed button for regular mode can override countdown timer operation.
