ROOF MOUNT SYSTEM INSTALLATION

1.Remove the collectors from the box and allow the collectors to relax in the sun (30 minutes to an hour). DO NOT LAY COLLECTORS ON THE GRASS IT CAN DAMAGE THE LAWN UNDERNEATH!

2.Allow at least one foot around the solar system for brackets, piping, and working area. Roof obstructions like vents should be taken into consideration when laying out collectors. With a roof vent up to 3" in diameter, the collectors can be placed on either side of the vent.

WARNING: DO NOT WALK ON THE SOLAR COLLECTORS

3.Determine the position of the top collector. Lay out the mounting brackets at each slot along the length of the collector. The collector should slope slightly toward the inlet point (where the water enters the collectors) to allow for drainage.

4.Drill 1/8" pilot hole for lag screws provided for all brackets. Lag screws should be long enough to reach the sub-roof under the shingles. Inject a generous amount of silicone sealant into the holes and onto the surrounding roof surface. Mount the bracket to the roof (as shown) with the bracket centered in the slot.

5.Remove and discard the black protective end caps covering the threaded ends of the header pipes at both ends of the collectors.

6.Slip the black rubber connector hoses with two 1 1/2" hose clamps over the ends of header pipes (as shown).

7.Position the hose clamps 1/2" in from each end of the rubber connector hose. Center them over the grooves on the header and tighten.

8.Begin tying the strap to the top bracket, run through the brackets below and tie to the bottom bracket (as shown).

WARNING:

DO NOT ADD ADDITIONAL NON-FACTORY APPROVED MOUNTING HARDWARE. DO NOT CLAMP HEADER PIPES DOWN.

YOU MAY DAMAGE YOUR COLLECTORS AND WILL VOID YOUR WARRANTY.

Note: When completed, you will have five vertical straps running across each collector. For high wind areas, we recommend one SK-34 High Wind Kit for each collector.

Call 1-888-560-7665 for ordering info.

DO NOT MOUNT COLLECTORS USING “C” CLAMPS ON HEADER PIPES!!

9.Install the vacuum relief end cap (provided in SK21) in the rubber hose (provided in SK21) located at the top corner of the system (see page 4) using hose clamps (provided). Install the rubber end cap (provided) at the diagonal bottom corner (as shown on page 4) using a hose clamp (provided).

4

6

8

10.Attach barbed end of the PVC to Hose Pipe Adapters (provided in SK21) to inlet and outlet headers using rubber hose connectors (provided) and hose clamps (provided). Attach smooth ends of the PVC of the Hose Pipe Adapters (provided) to your feed and return PVC pipes (as shown on page 4).

11.Inspect all clamps for proper position and tighten (DO NOT OVERTIGHTEN).

NOTE: LAYOUT PLUMBING BEFORE PRIMING AND GLUING.

12.Run your feed and return PVC pipe from the solar to the pool equipment as shown in the diagram provided.

13.Position the 3-Way Valve (provided) in a convenient area and connect (as shown).

14.Properly position the Check Valve (provided) between the filter and the 3-Way Valve (as shown on page 4) (with the arrow on the Check Valve pointing toward the 3-Way Valve). This will prevent water from flowing in the reverse direction into filter when

the pump is turned off.

15.Prime and glue all plumbing and fittings. When gluing PVC pipe, always wipe clean parts to be glued. Apply primer to parts being joined then swath with PVC glue. Connect parts and twist quarter turn for proper bonding.

YOU ARE NOW READY TO START-UP YOUR SOLAR POOL HEATER SYSTEM!

16.Start-up your system and check for leaks.

NOTE: Upon start-up you will see air bubbles come through the return. This is normal and will stop after all the air has been purged from the solar heating system. If not, switch the locations of the vacuum relief valve and the rubber end cap that will eliminate the problem.

5

Page 5
Image 5
SmartPool Inc S601 operation manual Roof Mount System Installation

S601 specifications

SmartPool Inc S601 is a state-of-the-art smart swimming pool system that epitomizes innovation and efficiency in modern aquatic leisure. Designed for both residential and commercial applications, the S601 model stands out due to its advanced features and user-friendly technology.

One of the main features of the S601 is its automated water management system. The system monitors pH levels, chlorine concentrations, and other water quality indicators in real time, ensuring that the pool environment remains safe and hygienic. This feature significantly reduces the need for manual testing and chemical adjustments, providing pool owners with a hassle-free experience.

The S601 is equipped with a smart filtration system that utilizes advanced nanotechnology to enhance water clarity and purity. This system not only filters out debris and particles but also breaks down contaminants at a molecular level, resulting in cleaner water with minimal reliance on harsh chemicals. This eco-friendly approach is a hallmark of SmartPool Inc's commitment to sustainability.

Another remarkable characteristic of the S601 is its integration with smart home technology. The pool system can be controlled remotely via a dedicated smartphone app. This allows users to adjust temperature settings, activate the filtration system, or even set up cleaning schedules from anywhere, enhancing convenience and efficiency. Furthermore, the app provides real-time notifications about water quality, maintenance needs, and energy consumption, empowering users to stay informed and proactive.

Energy efficiency is a key consideration in the design of the S601. The system incorporates solar heating elements and energy-efficient pumps that adapt to the pool's usage patterns. This not only reduces the operational costs but also minimizes the environmental footprint, making it a preferred choice for eco-conscious consumers.

Moreover, the S601 boasts a sleek, modern design with customizable aesthetic options. Users can select from various finishes, lighting settings, and water features to create a stunning visual appeal that complements their outdoor space.

In summary, SmartPool Inc S601 is at the forefront of smart pool technology, offering an unparalleled combination of automation, environmental sustainability, and design adaptability. Its cutting-edge features and user-friendly interface make it the perfect choice for those looking to elevate their swimming experience while minimizing maintenance and maximizing enjoyment.