User instructions, E7 E8 E9, Fault, Description | Smeg ST115S

E7

E8

E9

User instructions

FAULT	DESCRIPTION

	Turbine flow-regulator malfunction
	(for the relevant models only)
	The appliance is not able to "measure" the amount
	of water loaded accurately. Interrupt the program
	and switch off the dishwasher. Switch the
	dishwasher back on, program it again and start
	the washing cycle. If the problem persists, contact
	the after-sales service.

	Alternate washing system malfunction
	Interrupt the program and switch off the dishwasher.
	Switch the dishwasher back on, program it again and
	start the washing cycle. If the problem persists,
	contact the after-sales service.

	Water intake system malfunction
	Contact the after-sales service.
Light off	Light on	Light flashing

If an alarm occurs the appliance interrupts the program in progress and signals a fault.

•Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately.

•The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program.

•The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed.

To “reset” an alarm is necessary:

•Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again.

If the malfunction persists, contact your authorised Service Centre.

33

Image 34

Smeg ST115S User instructions, E7 E8 E9, Fault, Description, Turbine flow-regulatormalfunction, Light off, Light on

Contents

Page Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVED THIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCE 2. Installation and hook-up Installation instructions2.1 Water supply connection CONNECTING TO THE WATER SUPPLY DRAIN CONNECTION 2.2 Electrical connection and precautions L = brown N = blue = yellow-green Fuse replacement FOR GREAT BRITAIN ONLY SELECTED PROGRAM INDICATOR LIGHTS User instructions3. Description of the controls 3.1 Upper panel DELAYED START BUTTON SETTING THE WASHING PROGRAM AND SWITCHING ONDELAYED START LIGHTS User instructions SELECTING HALF LOAD WASH 3.2 Washing programsBefore starting a washing program make sure that available in all programs except the soak program CHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT END OF CYCLE REMOVING THE DISHES 4. Operating instructions 4.1Using the water softening system ADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLE ADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AID ADDING THE DETERGENT The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-freebut contain natural enzymes 4.3 General warnings and recommendations Items which are not dishwasher-safe LOWER BASKET 4.4 Using the basketsLOADING THE LOWER BASKET insert CUTLERY BASKETUPPER BASKET closed LOADING THE UPPER BASKET Loading examples Models with cutlery racks ADJUSTING THE UPPER BASKET Version B User instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1General warnings and recommendations •Fill the rinse aid dispenser CLEANING THE FILTER UNITPROLONGED DISUSE Shut off the water supply tap TROUBLESHOOTING MINOR PROBLEMS If the program fails to start, check that there is rinse aid inside the special container Safety level 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6 Alternate washing system malfunction E7 E8 E9Turbine flow-regulatormalfunction Water intake system malfunction Width TECHNICAL DATAWater supply pressure Electrical characteristics Height depending on models Capacity