Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC USB2513i Chapter 5 DC Parameters, 5.1Maximum Guaranteed Ratings, 5.2Recommended Operating Conditions, MIN, MAX, MIN, MAX, UNITS, Note:, UNITS, SYMBOL, SYMBOL, COMMENTS

1 48

Download 48 pages, 958.87 Kb

Industrial Temperature Rated USB 2.0 High-Speed 3-Port Hub Controller

Datasheet

Chapter 5 DC Parameters

5.1Maximum Guaranteed Ratings

PARAMETER	SYMBOL	MIN	MAX	UNITS	COMMENTS

Storage	TA	-55	150	°C
Temperature

Lead			325	°C	Soldering < 10 seconds
Temperature

1.8V supply	VDDA18PLL,		2.5	V
voltage	VDD18
3.3V supply	VDDA33,		4.6	V
voltage	VDD33PLL,
	VDD33,
	VDD33CR
Voltage on any		-0.5	5.5	V
I/O pin

Voltage on		-0.5	4.0	V
XTAL1

Voltage on		-0.5	3.6	V
XTAL2

Note: Stresses above the specified parameters could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any condition above those indicated in the operation sections of this specification is not implied. When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. When this possibility exists, it is suggested that a clamp circuit be used.

5.2Recommended Operating Conditions

PARAMETER	SYMBOL	MIN	MAX	UNITS	COMMENTS

Operating	TA	-40	85	°C
Temperature

1.8V supply voltage	VDDA18PLL	1.62	1.98	V
	VDD18
3.3V supply voltage	VDDA33	3.0	3.6	V
	VDDA33PLL
	VDD33
	VDD33CR
Voltage on any I/O pin		-0.3	5.5	V	If any 3.3V supply voltage drops
					below 3.0V, then the MAX
					becomes:
					(3.3V supply voltage) + 0.5

Revision 1.98 (11-19-07)	42	SMSC USB2513i
	DATASHEET

Contents

USB2513i Industrial Temperature Rated USB 2.0 High-Speed 3-PortHub Controller PRODUCT FEATURES ORDER NUMBERS: Table of Contents Chapter List of Figures List of Tables Chapter 1 Pin Configuration Figure 1.2 USB2513i 48-PinQFN Chapter 2 Block Diagram Chapter 3 Pin Descriptions 3.1PIN Descriptions Table 3.1 USB2514 Pin Descriptions (continued) Note: SERIAL PORT INTERFACE MISC Page Table 3.2 SMBus or EEPROM Interface Behavior CFG_SEL2 CFG_SEL1 CFG_SEL0 SMBUS OR EEPROM INTERFACE BEHAVIOR 3.2Buffer Type Descriptions Table 3.4 USB2514 Buffer Type Descriptions (continued) Chapter 4 Configuration Options 4.13-PortHub 4.1.1Hub Configuration Options 4.1.1.1Power Switching Polarity 4.1.2VBus Detect 4.3EEPROM Interface 4.3.1Internal Register Set (Common to EEPROM and SMBus) 4.3.1.1Register 00h: Vendor ID (LSB) 4.3.1.2Register 01h: Vendor ID (MSB) Register 02h: Product ID (LSB) 4.3.1.4Register 03h: Product ID (MSB) 4.3.1.5Register 04h: Device ID (LSB) 4.3.1.6Register 05h: Device ID (MSB) 4.3.1.7Register 06h: CONFIG_BYTE_1 4.3.1.8Register 07h: Configuration Data Byte 4.3.1.9Register 08h: Configuration Data Byte 4.3.1.10Register 09h: Non-RemovableDevice Register 0Ah: Port Disable For Self Powered Operation 4.3.1.12Register 0Bh: Port Disable For Bus Powered Operation 4.3.1.13Register 0Ch: Max Power For Self Powered Operation 4.3.1.14Register 0Dh: Max Power For Bus Powered Operation 4.3.1.15Register 0Eh: Hub Controller Max Current For Self Powered Operation 4.3.1.16Register 0Fh: Hub Controller Max Current For Bus Powered Operation 4.3.1.17Register 10h: Power-OnTime 4.3.1.18Register 11h: Language ID High 4.3.1.19Register 12h: Language ID Low 4.3.1.20Register 13h: Manufacturer String Length 4.3.1.21Register 14h: Product String Length 4.3.1.22Register 15h: Serial String Length 4.3.1.23Register 16h-53h:Manufacturer String 4.3.1.24Register 54h-91h:Product String Register 92h-CFh:Serial String 4.3.1.26Register F6h: Boost_Up 4.3.1.27Register F8h: Boost_3:0 4.3.1.28Register FAh: Port Swap Register FBh: Port Remap Register FCh: Port Remap Register FFh: Status/Command 4.3.2 I2C EEPROM 4.3.2.1Implementation Characteristics 4.3.2.2Pull-UpResistor 4.3.2.3I2C EEPROM Slave Address 4.3.3In-CircuitEEPROM Programming 4.4SMBus Slave Interface 4.4.1Bus Protocols 4.4.1.1Block Read/Write Slave Address Register Address 4.4.2Invalid Protocol Response Behavior 4.4.3General Call Address Response 4.4.4Slave Device Time-Out 4.4.5Stretching the SCLK Signal 4.4.6SMBus Timing 4.5Default Configuration Option: 4.6Default Strapping Options: 4.7Reset 4.7.1Internal POR Hardware Reset 4.7.2External Hardware RESET_N 4.7.2.1RESET_N for Strapping Option Configuration 4.7.2.2RESET_N for EEPROM Configuration 4.7.2.3RESET_N for SMBus Slave Configuration 4.7.3USB Bus Reset Page Chapter 5 DC Parameters 5.1Maximum Guaranteed Ratings 5.2Recommended Operating Conditions Table DC Electrical Characteristics I, IS Type Input Buffer Input Buffer with Pull-Up (IPU) Table 5.1 DC Electrical Characteristics (continued) IO-U Note CAPACITANCE TA = 25°C; fc = 1MHz; VDD18, VDDPLL Chapter 6 AC Specifications 6.1Oscillator/Clock 6.1.1SMBus Interface: 6.1.2I2C EEPROM: 6.1.3USB Chapter 7 Package Outlines Figure 7.2 48-PinQFN, 7x7mm Body, 0.5mm Pitch