Operation
! |
|
| WARNING |
| ! | Mulching (Recycling) Operation | ||||||
|
|
| Note: For best results, cut up to a maximum of 1/3 of grass | |||||||||
| DO NOT attempt any maintenance, adjustments or service | |||||||||||
| blade length and recycle ONLY when grass is dry. | |||||||||||
| with engine and blade running. STOP engine and blade. | |||||||||||
| 1. Set all wheels in the highest cutting position (Notch 7). | |||||||||||
| Disconnect spark plug wire and secure away from spark | |||||||||||
|
|
| Refer to the Section entitled “Cutting Height | |||||||||
| plug. Engine and components are HOT. Avoid serious |
|
| |||||||||
|
|
| Adjustment”. | |||||||||
| burns, allow sufficient time for all components to cool. |
|
| |||||||||
| 2. Move the engine speed control to the fast (Rabbit) | |||||||||||
|
|
|
|
|
|
|
|
|
| |||
Cutting Height Adjustment |
|
|
|
| position. | |||||||
|
| 3. Move the ground speed control to the slowest speed | ||||||||||
| 1. Pull the height adjusting latch (A, Figure 6) outward and |
|
| setting. | ||||||||
|
|
| move to the desired cutting height. |
|
| 4. Proceed mowing slowly. If the grass is very dense, | ||||||
|
|
|
|
|
|
|
|
|
|
|
| lower each rear wheel latch one notch lower than the |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| front wheel latches to improve mulching performance. |
|
|
|
|
|
|
|
|
|
| Note: The mulching cover should remain on the machine at | ||
|
|
|
|
|
|
|
|
|
| all times, unless alternate discharge operations are desired, | ||
|
|
|
|
|
|
|
|
|
| such as side discharging or bagging. | ||
|
|
|
|
|
|
| ReproductionFigure 8: Removing the mulching cover | |||||
|
|
|
|
|
|
|
|
|
| Removing the Mulching Cover | ||
|
|
|
|
|
|
|
|
|
| 1. Remove the nuts (A, Figure 8) securing the mulching | ||
|
|
|
|
|
|
|
|
|
|
|
| cover (B) to the m wer deck. |
|
|
|
|
|
|
| A |
|
| 2. | Remove he ver. | |
|
| Figure 6: Adjusting cutting height |
|
|
|
|
| B | ||||
| 2. Set all wheels at the same cutting height. The highest |
|
|
| ||||||||
|
|
| cutting position is Notch 7 (Figure 7). The lowest |
|
|
| ||||||
|
|
| cutting position is Notch 1. |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| A |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1.25 in |
|
| 4.00 in |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Figure 7: Cutting height settings (approximate) |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |
! |
|
| WARNING | ! |
|
|
|
Stop engine and mower blade by releasing the blade control before adjusting cutting height.
9