PRE-OPERATION CHECKLIST
Snapper has completed initial adjustments and performed operational tests prior to shipping the machine. Due to the possible effects of shipping, handling and storage, Snapper intends for all of the following items to be verified and necessary final adjustments made at time of setup. It remains good practice and is strongly recommended that all the items also be checked prior to placing the machine into service. It is very important that setup is verified and all operational tests completed and results are acceptable. After completing this form, sign and retain for future reference.
SET-UP CHECKLIST
_____ STEERING WHEEL and steering shaft assembled.
_____ TIE RODS connected.
_____ LUBRICATION of entire unit completed.
_____ OPERATOR’S SEAT installed and tightened and seat switch connected.
_____ FUEL TANK installed and fuel line connected.
_____ GRASS DEFLECTOR, MULCH COVER or CATCHER ADAPTER and assembly positioned, secured, checked.
_____ BATTERY activated and charged per instructions and installed into battery compartment on machine.
_____ TIRE inflated to proper Pounds per Square Inch (PSI). Front tire is 12 PSI and Rear tire is 12 PSI.
CUTTING BLADE & MOWER
_____ BLADE RETAINING hardware checked for proper tightness.
_____ BLADE TIP CLEARANCE inside lower edge of mower checked and corrected as needed.
_____ BLADE STRAIGHTNESS checked and adjusted as required.
_____ MOWER CUTTING HEIGHT settings checked and adjusted as needed (with tires properly inflated).
_____ MOWER SIDE TO SIDE level checked and adjusted as needed (with tires properly inflated).
_____ MOWER FRONT TO REAR setting checked and adjusted as needed (with tires properly inflated).
_____ BLADE LEVER checked and adjusted as required.
_____ BELT TENSION checked and adjusted as required.
_____ REVERSE LOCKOUT MECHANISM shifter will not go into reverse when blade pedals are depressed.
PRE-START CHECKS & SERVICES
_____ TIRES checked and inflated to correct pressures.
_____ ENGINE OIL level checked.
_____ DIFFERENTIAL check lubricant and add as needed.
_____ CHAIN CASE check lubricant and add as needed.
_____ YOKE ASSEMBLY checked for freedom of movement.
_____ FUEL added to tank and system checked for leaks. Refer to Engine’s Owner’s Manual for fuel specifications.
_____ BATTERY (not overfilled!) reinstalled and properly connected with red boot over positive terminal.
OPERATIONAL TESTS
_____ CHECK SEAT SWITCH for proper function
_____ INTERLOCK SYSTEMS checked to insure proper functioning.
_____ ENGINE STARTED and throttle control settings checked.
_____ IGNITION SWITCH checked to insure engine stops when turned to OFF position.
_____ PARKING BRAKE tested to insure proper operation.
_____ CLUTCH/BRAKE tested for proper operation and adjusted as required.
_____ BLADE STOPS in 3 seconds or less after releasing the blade pedal. Adjust blade brake as required.
_____ BLADE LEVER can be moved to OFF position with blade pedal depressed.
CONSUMER INFORMATION |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
SALE DATE |
| MACHINE MODEL |
|
|
|
|
|
| SERIAL NO. |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Retailer's Name |
|
|
| Signature |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Address _________________________ City |
|
|
|
|
|
|
|
| State | Zip | |||||||
|
|
|
|
|
|
|
|
|
| ||||||||
MACHINE WILL BE USED COMMERCIALLY? YES _________ NO |
|
|
|
| |||||||||||||
Purchaser's Name |
|
|
|
| Signature |
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||
Address _________________________ City |
|
|
|
|
|
|
|
| State | Zip | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IMPORTANT: This form is to be retained for future reference regarding Warranty, proof of purchase, traceability for product
recall or service, etc. Complete the Product Registration Card immediately and mail to: Customer Service Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253.
INSTRUCTION No. 7-5122 (I.R. 6/28/02)
4
