Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper CZT19481KWV Safety Messages And Symbols, Control Panel Identification, Stop, Fuel Gauge

Models: CZT19481KWV

1 40

Download 40 pages 44.09 Kb

Page 8

Image 8

Section 2 - SAFETY MESSAGES AND SYMBOLS

CONTROL PANEL IDENTIFICATION

DANGER! ROTATING BLADES

KEEP CHILDREN AND OTHERS OUT OF MOWING AREA

STOP

FUEL TANK SELECT

RUN

START

FUEL GAUGE (2)

IGNITION SWITCH

Page 8

Image 8

Snapper CZT19481KWV Safety Messages And Symbols, Control Panel Identification, Stop, Fuel Tank Select Run Start

Contents

COMMERCIAL MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES Safety Instructions & Operators Manual forMODELS CZT19481KWVIMPORTANT SAFETY INSTRUCTIONS PROTECTION FOR CHILDRENPROTECTION AGAINST TIPOVERS PROTECTION AGAINST TIPOVERSIMPORTANT SAFETY INSTRUCTIONS 11. Watch out for traffic when near or crossing roadwaysPREPARATION SAFE HANDLING OF GASOLINEIMPORTANT SAFETY INSTRUCTIONS MAINTENANCEMAINTENANCE 4. Check brakes frequently adjust, repair or replace as neededTABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTSMOTION CONTROL LEVER OPERATION WEAR HEARING PROTECTION PARKING BRAKE LEVER OPERATION WARNING ! AVOID SERIOUS INJURY OR DEATHSection 2 - SAFETY MESSAGES AND SYMBOLS IGNITION SWITCHCONTROL PANEL IDENTIFICATION DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREASection 2 - SAFETY MESSAGES AND SYMBOLS ROLL BAR PROTECTIVE STRUCTURE DECALSDO NOT allow operation of the machine by untrained personnel Section 3 - OPERATING INSTRUCTIONS3.1 PRE-START CHECK LIST 3.2.1. STARTING ENGINE Section 3 - OPERATING INSTRUCTIONS3.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE Section 3 - OPERATING INSTRUCTIONS 3.2.2. STOPPING ENGINE3.2.3. STARTING MOWER BLADES 3.2.4. STOPPING MOWER BLADES3.3 CUTTING HEIGHT ADJUSTMENT Section 3 - OPERATING INSTRUCTIONS3.4 OPERATION- MOTION CONTROLS 3.4.1. DRIVING MACHINEThere is no roll-over protection when roll bar is folded 3.6 SAFETY INTERLOCK SYSTEM CHECKSSection 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINESection 43 - MAINTENANCEOPERATING INSTRUCTIONS 4.2 SERVICE - AFTER FIRST 5 HOURS4.1 INTRODUCTION 4.2.1. CHANGE ENGINE OIL Change engine oil as followsSection 43 - MAINTENANCEOPERATING INSTRUCTIONS 4.2.3. CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting4.3 AFTER EVERY 25 OPERATING HOURS 4.3.1. ENGINE 4.3.2. MOWER COMPONENTS 1. Mower Drive BeltSection 43 - MAINTENANCEOPERATING INSTRUCTIONS 4.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings4.4 BEFORE OPERATING MACHINE 4.5 ANNUALLY END OF EACH SEASONContinued On Next Page Section 43 - MAINTENANCEOPERATING INSTRUCTIONS4.6 DECK REMOVAL Section 43 - MAINTENANCEOPERATING INSTRUCTIONS 4.7 HYDRAULIC FLUID FILTERContinued On Next Page Section 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR5.1 NEUTRAL POSITION ADJUSTMENTS Section 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS Continued From Previous Page5.2 MOWER DECK & COMPONENT ADJUSTMENTS 5.2.1. MOWER DECK ADJUSTMENT LEVELNESSSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.2.1. MOWER DECK ADJUSTMENT LEVELNESS SIDE to SIDE and FRONT to REAR5.3 PARKING BRAKE ADJUSTMENT a. Disengage parking brakeSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.4 TRACTION BELT REPLACEMENT5.6 TRACKING ADJUSTMENT 5.3 TRACTION BELT TENSIONSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.7.2. BELT REPLACEMENTBELT ADJUSTMENT FIGURE 5.12a 5.7 MOWER DRIVE BELT REPLACEMENT AND ADJUSTMENTSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.8 ENGINE ADJUSTMENTS & REPAIR5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 5.9.2. BLADE SHARPENINGSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.10BATTERY 5.10.1. BATTERY REMOVAL5.10.2. BATTERY INSTALLATION 5.10.3. BATTERY CHARGINGSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR Battery Condition Chart5.10.4. BATTERY TESTING 5.10.5. NEW BATTERY PREPARATION 1. Remove battery from cartonSection 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR 5.11HYDRAULIC SYSTEM, PURGINGSectionTROUBLESHOOTING3 - OPERATING INSTRUCTIONS PROBLEMPROBABLE CAUSE CORRECTIVE ACTIONSectionTROUBLESHOOTING3 - OPERATING INSTRUCTIONS PROBLEMBattery Will Not Charge PROBABLE CAUSESERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS MAINTENANCE/REPLACEMENT PARTSSERVICE Air Cleaner2 YEAR LIMITED WARRANTY DISCLAIMER OF WARRANTYPRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atPage Page MANUAL No. 7100237 I.R. 7/14/2005 Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. PhoneCOMMERCIAL MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES