TROUBLESHOOTING
PROBLEM |
| PROBABLE CAUSE |
Engine Will Not | 1. | Fuel tank empty. |
Start Using | 2. | Engine needs choking. |
Recoil Starter | 3. | Spark plug wire disconnected. |
| 4. | Faulty parking brake, blade or ignition switch. |
| 5. | Park brake not engaged. |
| 6. | Ignition is in the OFF position. |
Engine Will Not | 1. | Fuel tank empty. |
Start Using | 2. | Engine needs choking. |
Electric Starter | 3. | Spark plug wire disconnected. |
4.Faulty parking brake, blade or ignition switch.
5.Park brake not engaged.
6.Blown Fuse.
7.Faulty interlock module.
8.Ignition is in the OFF position.
9.Battery is weak or dead.
10.Battery cables loose, broken disconnected or corroded.
11.Faulty electric starter or starter solenoid.
12.Starter cable loose, broken or disconnected.
13.Electrical wiring harness disconnected or broken. Engine Stalls After 1. Operator not in seat.
Running | 2. Choke control in the “CHOKE” position. | |
| 3. | Fuel tank empty. |
| 4. | Engine air |
| 5. | Spark plug defective or gap set improperly. |
| 6. | Fuel filter restricted. |
| 7. | Water, debris or stale fuel in fuel system. |
| 8. | Vent on fuel cap closed. |
Engine Loses | 1. Excessive load on engine. | |
Power | 2. Engine air | |
| 3. | Spark plug faulty. |
| 4. | Water, debris or stale fuel in fuel system. |
| 5. | Debris build up on engine cooling screen. |
|
| |
Engine Backfires | 1. Throttle control set too “FAST”. | |
When Turned To |
|
|
“STOP” |
|
|
Excessive Vibration | 1. Damaged, out of balance or bent mower blades. | |
| 2. | Loose blade components. |
| 3. | Loose or missing air lift (if equipped). |
| 4. | Lumpy or frayed belt. |
| 5. | Bent Idler, stationary or spindle pulley. |
CORRECTIVE ACTION
1.Fill fuel tank with fresh fuel to proper level.
2.Move choke control to “CHOKE” position.
3.Place spark plug wire onto spark plug.
4.Contact authorized SNAPPER dealer.
5.Engage park brake.
6.Turn ignition switch to the ON position.
1.Fill fuel tank with fresh fuel to proper level.
2.Move choke control to “CHOKE” position.
3.Place spark plug wire onto spark plug.
4.Contact authorized SNAPPER dealer.
5.Engage park brake.
6.Replace with new 20 AMP fuse.
7.Contact authorized SNAPPER dealer.
8.Turn ignition switch to the START position.
9.Charge or replace with new battery.
10.Clean and connect battery cables. If broken, replace with new battery cables.
11.Contact authorized SNAPPER dealer.
12.Connect starter cable. If broken, replace with new starter cable.
13.Connect or replace with new wiring harness.
1.Sit in operator’s seat.
2.Move choke control to “OFF” position.
3.Fill fuel tank with fresh fuel to proper level.
4.Clean free of all debris.
5.Service spark plug.
6.Replace fuel filter.
7.Drain and clean fuel system.
8.Open vent.
1.Lessen load.
2.Clean or replace filters.
3.Service spark plug.
4.Drain and clean fuel system. Replace filter.
5.Clean all debris from engine cooling screen.
1.Set throttle control to “SLOW” and allow engine to idle. Then, turn key to “OFF”.
1.Service mower blade(s).
2.Service and tighten loose parts.
3.Replace air lifts. Tighten to proper torque.
4.Replace belt.
5.Replace pulley.
(Trouble Shooting Continued on Next Page)
31
