Snapper setup guide Items that you will need, Items Included, S22675 - NS22675 Overview

Quick Setup Guide

Push Mower Models S22675 - NS22675

Questions?Do not return to the store. We can help.

Call Customer Service Toll-Free 1-800-317-7833Or visit our website www.snapper.com

S22675 - NS22675 Overview

Bail Control

Recoil Rope

Handle

	1	Unpack the mower		5	Add oil and fuel	B	A
•	Remove the mower from the carton. Remove all packing materials from the mower.		•	Move the mower outside to a flat, level surface.
•	Locate and identify the items included with the mower.		•	Remove the oil fill cap (A, Figure 3). Add the entire contents of the
				supplied oil container to the engine. Replace the oil fill cap.

2				Failure to read and follow instructions in the				Figure 3
	Read the manuals			operator's manual could result in death and/or		IMPORTANT Mower is shipped without oil in engine.
				bodily injury.
						Failure to add oil will result in engine damage.
• Carefully read all the manuals supplied with the mower. They contain important safety, operating, and					• Remove the fuel fill cap (B). Following the three-step instructions on the			DANGER
maintenance information.
						FrestStartTM card, snap the fuel preserver cartridge into the bottom of
						the fuel fill cap.		Fuel stabilizer is a hazardous chemical.
								IF SWALLOWED, call a physician immediately.
3					•	Add clean, fresh, UNLEADED fuel with a minimum of 87 octane, leaving		Fuel stabilizer contains:
	Unfold the handle					one inch of space from the top of the tank for fuel expansion.		2,6-di-tert-butylphenol (128-39-2) and
								aliphatic petroleum distillate (64742-47-8).
						IMPORTANT Fuel tank holds less than 1/2 gallon.
• Turn the knobs (A, Figure 1) on either side						IMPORTANT DO NOT mix oil with fuel.
of the lower handle 1/4 turn to retract the				B		IMPORTANT DO NOT use E85 fuel.
locking pins.								Running engines give off carbon monoxide, an
					•	Replace the fuel fill cap, and wipe up any spills.
								odorless, colorless, poison gas. Breathing carbon
• Raise the lower handle, aligning it with one								monoxide can cause nausea, fainting, or death.
of the three sets of holes in the handle								Operate this product ONLY outdoors.
bracket (most users will prefer the middle				A				Keep exhaust gas from entering a confined area through
								windows, doors, ventilation intakes or other openings.
position).
				for				DO NOT operate this product inside any building or
								enclosure, even if windows and doors are open.
• Turn the knobs to release the locking pins
and secure the lower handle.
NOTE: The lower handle on some models
features removable hardware in place of the								A
retractable knobs.						6
							Start the mower	A
• Loosen, but do not remove, the upper
knobs (B) on the handle. Remove the					•	Move the cutting height adjust levers (A, Figure 4) to the desired
cardboard slats.						cutting height.
• Raise the upper handle to the operating			Figure 1		•	Set the mower to mulch, discharge or bag. (See 3-in-1 instructions below.)		Figure 4
position, and tighten the upper knobs.
		Not

Fuel Fill Cap

Mulching

Cover

Cutting Height Adjust Lever

(At Each Wheel)

Items that you will need

Oil Fill and

Dipstick

					• Hold the bail control (A, Figure 5) against the drive handle.
	4 Set up the recoil rope handle				• Pull the recoil rope handle (B) until the engine starts.
					• To stop the engine and blade, release the bail control.
	• Hold the bail control (A, Figure 2) against the handle,			B			B
	and pull the recoil rope handle out to the ro e							A
	guide (B) on the handle. Hook the recoil ro e			A
	into the rope guide (it might be a tight fit).
			Figure 2
							Figure 5
3-in-1: Convert from mulching to bagging to side-discharge:
		Reproduction
1	For mulching:		2	To convert to bagging:	A	3 To convert to side-discharge:		A

Utility Knife

Unleaded Fuel (minimum 87 octane)

Items Included

Side Discharge

Deflector

FreshStartTM Fuel

Preserver Cartridge

• Leave the mulching cover		• Lift the rear door (A, Figure 7).
(Figure 6) in place.		• Holding the rear door open, attach the
		grass catcher (B) to the rear of the mower.
		• Make sure the hooks (A, Figure 8) on
		either side of the catcher frame hook
		onto the rear door rod (B).
	Figure 6
		• Release the rear door (it will lay on top of
		the grass catcher).

•Lift the mulching cover (A, Figure 9).

•Install the side discharge deflector (B) onto

		the mower deck. Make sure the upper tabs (A,
	B	Figure 10) of the deflector are hooked behind
		the mulching cover rod, and the deck tabs
Figure 7
		stick up through the locking slots (B).
	A	• Release the mulching cover (it will lay
		on top of the side discharge deflector).

B

Figure 9

A

Grass Catcher	SAE30W	Operator’s
	Oil	Manual

B

Figure 8

B

Figure 10

© Briggs & Stratton Corporation
We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.	Form No. 7104975 (Rev. ‘-’, 11/11/2010)