Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH Adjustments & Repair

Models: NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV

1 40

Download 40 pages 46.21 Kb

Page 27

BEARING REPLACEMENT

Section 5 - ADJUSTMENTS & REPAIR

5.11 MOWER SPINDLES (Field Serviceable Spindles)

BEARING REPLACEMENT

In the event that a spindle bearing requires

replacement, the SNAPPER Field Serviceable

Spindles have been designed so that no special

tools or presses are required.

1. Remove belt. Loosen blade nut and remove.

Allow blade bolt, washer, blade and four spacers

to drop down out of the spindle housing. See

Figure 5.19.

IMPORTANT: Spindle housing must be filled with grease before operating mower. Failure to fill housing will cause premature bearing failure.

REMOVE NUT

REMOVE BELT

FROM SPINDLE

REMOVE BLADE

BOLT

FIGURE 5.19

2.	Remove spindle pulley from spindle shaft.
3.	Locate circular retaining ring on spindle shaft at
top bearing. Remove retaining ring. Allow spindle
shaft to drop out of housing.
4.	Top and bottom bearings are now removable.
Pull out on inner race to slide bearing from
housing. See Figure 5.20.
5.	Thoroughly clean all parts removing all old
contaminated grease.
6.	Install new bottom bearing first.
7.	NOTE: The bearing is sealed/shielded on one
side only. The bottom bearing must be installed
with the sealed/shielded side DOWN.
8.	Insert spindle shaft up through the bottom

BEARING

SEAL UP

BEARING SEAL DOWN

PULLEY

SPACER

NYLOS SEAL

RETAINING RING

BEARING

SPINDLE

HOUSING

SPACER

BEARING

SPINDLE SHAFT

bearing. Slide spacer down over spindle shaft.
9. Install new top bearing. Install the top bearing
with the seal/shield UP.
10.	Slide circular retaining ring down spindle shaft
until it fully locks into groove on shaft.
11.	Apply a generous amount of general-purpose
grease to the concave side of the nylos seal.
Install the nylos seal with concave greased side
down.
12.	Place spindle pulley and spacer on top of
spindle shaft.
13.	Reinstall blade bolt, washer, blade and four
spacers. See Figure 5.15
14.	Torque blade bolt and nut to 70 to 80 ft. lbs.
15.	Pump grease into spindle housing until grease
purges from vent on housing.
16.	After the first 5 hours of operation, grease
spindle housing to insure it is full, then every 25
hours.

FIGURE 5.20

27

Image 27

Snapper NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH Adjustments & Repair, Bearing Replacement

Contents

NZM19482KWV NZM21522KWV NZM25612KWV NZM27612KH Safety Instructions & Operator’s Manual forMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES MODELSPROTECTION AGAINST TIPOVERS IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PROTECTION AGAINST TIPOVERSOPERATION IMPORTANT SAFETY INSTRUCTIONSPREPARATION SAFE HANDLING OF GASOLINEOPERATION IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE MAINTENANCETABLE OF CONTENTS differ from your specific model. Contact Section 1 - FAMILIARIZATIONThe figures and illustrations in this manual are provided for reference only and mayWEAR HEARING PROTECTION WARNING ! AVOID SERIOUS INJURY OR DEATH Section 2 - SAFETY MESSAGES AND SYMBOLSDANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS MOTION CONTROL LEVER OPERATION PARKING BRAKE LEVER OPERATIONDANGER! ROTATING BLADES IGNITION SWITCH Section 2 - SAFETY MESSAGES AND SYMBOLSPUSH SWITCH “DOWN” TO KEYSWITCHSection 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LISTDO NOT allow operation of the machine by untrained personnel Section 3 - OPERATING INSTRUCTIONS 3.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE3.2.1. STARTING ENGINE LEVER SHOWN IN THE NEUTRAL LOCK POSITION KEYSWITCH SHOWN FROM OPERATOR’S VIEW POINTSection 3 - OPERATING INSTRUCTIONS PARKING BRAKE LEVER IN ENGAGED “ON” POSITION MOTION CONTROL LEVER3.3 CUTTING HEIGHT ADJUSTMENT Section 3 - OPERATING INSTRUCTIONS3.4 OPERATION- MOTION CONTROLS 3.4.1. DRIVING MACHINE 2. Engage parking brake Section 3 - OPERATING INSTRUCTIONS4.2.1. CHANGE ENGINE OIL Change engine oil as follows Section 4 - MAINTENANCE4.2 SERVICE - AFTER FIRST 5 HOURS 4.1 INTRODUCTION4.2.3. CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting Section 4 - MAINTENANCE3. Other Lubrication Points Section 4 - MAINTENANCE4.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings 2. Hydro Pumps4.6 DECK REMOVAL Section 4 - MAINTENANCE4.7 HYDRAULIC FLUID FILTERS Section 4 - MAINTENANCEDANGER Section 5 - ADJUSTMENTS & REPAIR5.2.1. MOWER DECK ADJUSTMENT LEVELNESS Section 5 - ADJUSTMENTS & REPAIR5.1 NEUTRAL POSITION ADJUSTMENTS Continued From Previous Page 5.2 MOWER DECK & COMPONENT ADJUSTMENTSSection 5 - ADJUSTMENTS & REPAIR 8. Move deck lift lever and set the mower deck tothe highest cutting position and recheck side to side The traction drive belt tension does not require Section 5 - ADJUSTMENTS & REPAIR5.7.2. BELT REPLACEMENT Section 5 - ADJUSTMENTS & REPAIR5.6 TRACKING ADJUSTMENT 5.7 MOWER DRIVE BELT REPLACEMENT5.9.2. BLADE SHARPENING Section 5 - ADJUSTMENTS & REPAIR5.8 ENGINE ADJUSTMENTS & REPAIR 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS5.10 BATTERY 5.10.1.BATTERY REMOVAL Section 5 - ADJUSTMENTS & REPAIRBattery Condition Chart Section 5 - ADJUSTMENTS & REPAIRBEARING REPLACEMENT Section 5 - ADJUSTMENTS & REPAIR5.12 HYDRAULIC SYSTEM, PURGING Section 5 - ADJUSTMENTS & REPAIRPROBABLE CAUSE TROUBLESHOOTINGPROBLEM Trouble Shooting Continued on Next PageLoss Of Traction TROUBLESHOOTINGBattery Will Not Charge Machine Will Not Move48” DECK SERVICE SCHEDULEMAINTENANCE PARTS MAINTENANCE/REPLACEMENT PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Call the Snapper Customer Relations Center at SNAPPER PRODUCT REGISTRATION FORMPage Page Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIESMANUAL No. 7-4408 Rev. 1 - 9/3/04