Snapper P216012E Troubleshooting, Problem, Probable Cause, Corrective Action

Models: P216012E

1 28
Download 28 pages 58.55 Kb
Page 21
Image 21

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

 

Engine Will Not Start

1.

Battery is dead.

1.

Charge or replace battery.

Using Electric Starter

 

 

 

 

2.

Wiring harness to battery disconnected.

2.

Connect wiring harness and tighten securely.

 

 

 

 

 

 

3.

Spark plug wire disconnected.

3.

Place spark plug wire onto spark plug.

 

 

 

 

 

Engine Will Not Start

1.

Fuel tank empty.

1.

Fill fuel tank with fresh fuel.

Using Recoil Starter

 

 

 

 

2.

Engine needs choking or priming.

2.

Choke/Prime engine. Check Engine Manual for

 

 

 

 

instructions.

 

3.

Spark plug wire disconnected.

3.

Place spark plug wire onto spark plug.

 

 

 

 

 

4.

Key switch is not in the “RUN” position.

4. Turn key switch to the “RUN” position.

 

 

 

 

Engine Stalls or Stops

1.

Blade control is released or is not being held

1. Blade control should be held securely against

After Running

 

securely against handle.

 

handle at all times during operation of mower.

 

2.

Fuel tank empty.

2.

Fill with fuel to proper level.

 

 

 

 

 

 

3.

Engine air pre-cleaner and or air cleaner dirty.

3.

Clean free of all debris.

 

 

 

 

 

 

4.

Spark plug defective or gap set improperly.

4.

Service spark plug.

 

 

 

 

 

 

5.

Water, debris or stale fuel in fuel system.

5.

Drain and clean fuel system.

 

 

 

 

 

Engine Loses Power

1.

Engine air pre-cleaner or air cleaner dirty

1.

Clean or replace filters.

 

 

 

 

 

 

2.

Spark plug faulty.

2.

Service spark plug.

 

3.

Water, debris or stale fuel in fuel system.

3.

Drain and clean fuel system.

 

 

 

 

 

Excessive Vibration

1.

Damaged, out of balance or bent mower blade.

1.

Service mower blade.

 

 

 

 

 

 

2.

Loose blade components.

2.

Service and tighten loose parts.

 

 

 

 

 

 

3.

Loose or missing air lift (if equipped).

3.

Replace air lifts. Tighten to proper torque.

 

 

 

 

 

 

4.

Lumpy or frayed belt.

4.

Replace belt.

 

 

 

 

 

 

5.

Bent Idler pulley.

5.

Replace pulley.

 

 

 

 

Mower Will Not Move

1. Damaged transmission.

1.

Contact authorized SNAPPER dealer.

Loss Of Traction

2. Traction drive belt requires replacement.

2.

Replace traction drive belt.

(Self-Propelled Models)

3. Driven disc slipping.

3.

Clean or replace driven disc.

 

 

 

 

Cutting Grass

1. Cutting height too low or high.

1.

Adjust cutting height.

 

 

 

Improperly

2. Engine speed too slow.

2. Move engine speed control to “FAST” position.

 

 

 

 

 

3. Forward ground speed too fast.

3.

Move ground speed control to a slower speed.

 

 

 

 

 

4. Terraced cut, side to side.

4.

Adjust height of cut with height adjust levers.

 

 

 

 

 

5. Excessive deck pitch, front to rear.

5.

Adjust height of cut with height adjust levers.

 

 

 

 

 

6. Cutting blade dull or damaged.

6.

Sharpen cutting edges or replace blade.

 

 

 

 

Poor Grass Discharge

1. Engine speed too slow.

1.

Move engine speed control to “FAST” position.

 

 

 

 

 

2. Forward speed too fast.

2.

Move ground speed control to a slower speed.

 

 

 

 

 

3. Grass is wet.

3.

Mow when grass is dry.

 

 

 

 

 

4. Excessively worn or damaged blade.

4.

Service mower blade.

 

 

 

 

 

5. Build up of grass clippings and debris under deck.

5.

Clean deck.

 

 

 

 

 

6. Improper blade installed on deck.

6.

Install proper SNAPPER blade.

 

 

 

 

 

7. Blade installed improperly on deck.

7.

Install blade properly.

 

 

 

 

Oil Leaking

1. Leaking engine case.

1.

Contact authorized SNAPPER dealer.

 

 

 

2.

Check and tighten drain plug.

 

 

 

3.

Make sure dip stick or oil filler cap is securely in

 

 

 

 

place.

21

Page 21
Image 21
Snapper P216012E important safety instructions Troubleshooting, Problem, Probable Cause, Corrective Action