Section 3 - MAINTENANCE

3.1INTRODUCTION

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.

3.2SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

1.Disconnect spark plug wire and secure end away from plug. The items needed to perform oil change are: cloth rags, (1) 3/8” drive ratchet with a short extension and (1) shallow pan.

2.Tilt mower up on its rear wheels for access to the oil drain plug located underneath the mower deck. Do not tilt mower with spark plug or carburetor down. See Figure 3.1.

DRAIN PLUG

FIGURE 3.1

3.Place shallow pan underneath the approximate center of the oil drain plug.

4.Loosen with ratchet and short extension, but do not remove oil drain plug. Loosen plug until you can turn it with your fingers.

5.Lower the mower down and place the piece of wood under left rear wheel. Reach under mower and remove drain plug and allow oil to drain out completely in pan. Some oil may spill onto hands, immediately wipe hands clean with cloth rags.

6.Tilt mower back up and replace drain plug. Tighten securely but do not over tighten.

7.Fill engine with oil as specified in Engine Owner’s Manual.

8.Check air cleaner and perform air filter maintenance as specified in the Engine Owner’s Manual.

IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.2.2. CHECK MOWER BLADE

1.Disconnect spark plug wire and secure end away from plug.

2.Tilt mower up on its rear wheels for access to the blade cap screw. Do not tilt mower with spark plug or carburetor down. See Figure 3.2.

3.Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs. of torque. See Figure 3.2.

4.Check blade for sharpness, wear and damage. Refer to Section “Blade Wear Limits”.

BLADE

CHECK TORQUE OF BLADE

RETAINING

SCREW

RETAINING SCREW

 

TORQUE TO 30 to 40 FT. LBS.

 

FIGURE 3.2

WARNING

To avoid spilling fuel, empty engine gas tank before tilting mower.

11

Page 10 Page 12
Page 11
Image 11
Snapper R1962519B Maintenance, Service After First 5 Hours 3.2.1. Change Engine OIL, Check Mower Blade
Page 10 Page 12

R1962519B specifications

The Snapper R1962519B is a powerful and efficient lawn mower designed for homeowners who value a well-manicured lawn. With its robust engineering and user-friendly features, this mower stands out in the competitive landscaping equipment market.

One of the key features of the Snapper R1962519B is its 19-inch cutting deck, which allows for a wider cutting path compared to many traditional mowers. This feature enables quicker mowing, making it an ideal choice for those with moderate to larger-sized lawns. The mower is equipped with a 190cc Briggs & Stratton engine, known for its reliability and performance. This engine provides ample power to tackle thick grass and varying terrain types with ease.

The R1962519B utilizes a 3-in-1 cutting system, which means it can mulch, bag, or side discharge grass clippings based on user preference. This versatility not only enhances the mower's efficiency but also allows homeowners to choose the best method for lawn maintenance depending on the season or specific yard conditions.

Another innovative feature of this model is its variable speed self-propel system. This technology allows users to adjust their mowing speed, providing greater control and comfort while mowing. Whether you need to navigate around garden beds or speed through open areas, the Snapper R1962519B adapts to your pace.

Comfort is further enhanced by the adjustable ergonomic handle, which can be customized to suit the user's height and posture. This thoughtful design reduces strain during operation, making it easier to handle and maneuver the mower, particularly on longer mowing sessions.

In terms of construction, the Snapper R1962519B is built with durable materials that withstand rugged outdoor use. The deck's design also promotes optimal airflow, resulting in improved cutting performance and a cleaner finish.

Maintenance is simplified through features such as a quick-change oil system and easy-access air filter. This ensures that users can perform necessary upkeep without needing specialized tools or knowledge.

In summary, the Snapper R1962519B combines practical features, cutting-edge technologies, and thoughtful design to provide an excellent mowing experience. With its powerful engine, versatile cutting options, and user-friendly controls, it is a fantastic choice for anyone looking to maintain a beautiful lawn with minimal effort.
Top Page Image Contents