Section 3 - MAINTENANCE

3.1INTRODUCTION

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.

3.2SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL

WARNING

Before attempting any adjustments or repairs, STOP the engine, remove the spark plug wire from the spark plug and secure wire away from plug. Engine oil is extremely hot and can cause severe burns. Allow engine oil to cool before draining to prevent injury.

1.Disconnect spark plug wire and secure end away from plug. The items needed to perform oil change are: (2) cloth rags, (1) 3/8” drive ratchet with a short extension and (1) shallow pan.

2.Tilt mower up on its rear wheels for access to the oil drain plug located underneath the mower deck. Do not tilt mower with spark plug or carburetor down. See Figure 3.1.

REMOVE

OIL PLUG

FIGURE 3.1

3.Place shallow pan underneath the approximate center of the oil drain plug.

4.Loosen with ratchet and short extension, but do not remove oil drain plug. Loosen plug until you can turn it with your fingers.

5.Lower the mower down and place the piece of wood under left rear wheel. Reach back under mower and remove drain plug and allow oil to drain out completely in pan. Some oil will spill onto hands, immediately wipe hands clean with cloth rags.

6.Tilt mower back up and replace drain plug. Tighten securely but do not over tighten.

7.Fill engine with oil as specified in Engine Owner’s Manual. Thereafter, change oil after each 25 hours of use.

3.3ANNUALLY (END OF EACH SEASON)

Perform all maintenance as described in the maintenance schedule.

3.3.1. Engine

Service engine according to engine owner’s manual.

3.3.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain fuel from fuel tank and let engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into exhaust or air intakes during washing.

4.Tilt mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.Loosen handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

7.Store the mower in a shed or other dry area, protected from weather.

7

Page 6 Page 8
Page 7
Image 7
Snapper NR205012, R204513E, R205012 Maintenance, Service After First 5 Hours 3.2.1. Change Engine OIL, Storage Procedure
Page 6 Page 8

NR205012, R204513E, R205012, R205012, NR205012 specifications

Snapper NR205012, R204513E, R205012, and NR205012 are essential models in the Snapper lineup, renowned for their performance, reliability, and advanced features tailored for gardening enthusiasts and landscaping professionals alike. These models boast powerful engines designed for efficiency and durability, ensuring that users can tackle various tasks with ease.

One of the main features of the Snapper NR205012 model is its robust 20-inch cutting deck, which offers exceptional maneuverability and precision in cutting. This feature enables users to navigate around tight corners and obstacles, making it ideal for residential yards and commercial landscaping projects. The R204513E, on the other hand, incorporates an advanced rear-wheel drive system that enhances traction and control on uneven terrains, allowing for a seamless mowing experience.

In terms of technology, the Snapper lineup is equipped with innovative engine designs that provide fuel efficiency without compromising power. The overhead valve (OHV) technology used in these models ensures cooler operation and reduced emissions, contributing to a lower environmental impact. Furthermore, the Self-Propelled Drive System featured in the R205012 allows for easy handling, even during longer mowing sessions, while significantly reducing user fatigue.

The NR205012 model is designed with user comfort in mind. It features an adjustable handle height, providing ergonomic support to accommodate different user preferences. This attention to comfort is coupled with easy-to-use controls that minimize complexity, making the mowing experience enjoyable for both seasoned landscapers and novice users.

Durability is another hallmark of the Snapper NR205012 series. Built with high-quality materials, these models are designed to withstand heavy use, ensuring they can operate in demanding conditions over time. The rust-resistant components and reliable construction ensure that users can enjoy a long-lasting product, reducing the need for frequent replacements or repairs.

In summary, Snapper NR205012, R204513E, R205012, and NR205012 embody a blend of power, technology, and user-friendly features, making them excellent choices for anyone looking to enhance their lawn care routine. With their efficient engines, innovative drive systems, and focus on durability, these models are positioned as leaders in the world of outdoor power equipment, delivering exceptional performance and ease of use across various applications. Whether for home gardens or professional landscaping, Snapper ensures that users can achieve immaculate results with every cut.
Top Page Image Contents