Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper WMR216517B, WMRP216517B Familiarization, Introduction, Nomenclature

Models: WMRP216517B WMR216517B, WMRP216517B

1 28

Download 28 pages 8.34 Kb

Page 5

Section 1 - FAMILIARIZATION

Section 1 - FAMILIARIZATION

ROPE	UPPER
START	HANDLE
HANDLE

MID-HANDLE

BLADE CONTROL

KNOB

FUEL

FILLER

CAP

KNOB

REAR HEIGHT

ADJUSTMENT

LEVER

REAR WHEEL

GRASS BAG ADAPTER

PRIMER BULB (SEE INSET)

BRIGGS & STRATTON ENGINE

PRIMER BULB –

LOCATED AT FRONT OF ENGINE

ENGINE AIR

FILTER COVER

MUFFLER

MOWER

DECK

FRONT HEIGHT
ADJUSTMENT	FRONT WHEEL
LEVERS	FRONT WHEEL

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices.

Read, Understand and Follow the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3 of this manual and all safety messages on the mower and attachments before operating the mower.

1.2 NOMENCLATURE

The nomenclature drawing above, Figure 1.1, shows the essential parts of the SNAPPER WALK BEHIND MOWERS. It is recommended that all operators of the mower become thoroughly familiar with the controls, parts and operation of the mower before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference.

5

Image 5

Snapper WMR216517B, WMRP216517B important safety instructions Familiarization, Introduction, Nomenclature

Contents

21” STEEL DECK WALK MOWERS “M” MODEL SERIES Safety Instructions & Operator’s Manual forMODELS PUSHPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE AND STORAGE TABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION 2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECK LIST 2.5 CUTTING HEIGHT ADJUSTMENT 2.4 HANDLE HEIGHT ADJUSTMENTSection 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION2.6 RECYCLING OPERATION Section 2 - OPERATING INSTRUCTIONSB. Position grass bag between handles. See Figure Section 2 - OPERATING INSTRUCTIONSA. Remove grass bag from handle and bag adapter. See Figure Section 2 - OPERATING INSTRUCTIONSSection 3 - MAINTENANCE KEEP DRIVE DISC CLEAN Section 3 - MAINTENANCESection 4 - ADJUSTMENTS & REPAIR 4. Sharpen blade on a grinding wheel at an angle of Section 4 - ADJUSTMENTS & REPAIR1. Grease on drive disc causing slippage Section 4 - ADJUSTMENTS & REPAIR2. Remove driven disc spring from driven disc assembly. Loosen connector hex nut. See Figure Section 4 - ADJUSTMENTS & REPAIRDRIVEN DISC ASSEMBLY Section 4 - ADJUSTMENTS & REPAIRINSTALL NEW DRIVEN DISC SNAP3. Remove holder, O-ring and bearing 4. Install new bearing Section 4 - ADJUSTMENTS & REPAIRassembly removal procedure Section 4 - ADJUSTMENTS & REPAIRPROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE3 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Call the Snapper Customer Relations Center at SNAPPER PRODUCT REGISTRATION FORMSafety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS “M” MODEL SERIES