SET-UP INSTRUCTIONS & PRE-OPERATION CHECKLIST SNAPPER LARGE FRAME ZERO TURNING Z-RIDER with MID MOUNT MOWER

INTRODUCTION: These instructions cover the set-up of the Snapper Large Frame Mid Mount Z-Rider Mower. Complete each of the following steps carefully. Review and complete each item as instructed on the Pre-Operation checklist. The Snapper Product Registration card must be filled out and sent to Customer Service department at Snapper when completed.

IMPORTANT: The battery for this unit is maintenance-free. It is filled with acid and is sealed. Do not attempt to open the battery. Pay close attention to the precautionary statements on the battery and in these instructions. If charging is needed (see below), you will need an automotive type battery charger to activate the battery for use.

STEP 1: Remove machine from the container.

STEP 2: Assemble motion control levers:

A. Carefully remove wire ties securing folded handles to machine.

B. Remove noted hardware from motion control lever blocks. See Figure 1.

C. Unfold motion control lever handles, and secure with removed hardware. See Figure 1. Tighten all hardware securely.

NOTE: Motion control levers may require adjustment. Refer to Operator’s Manual for adjustment procedures.

UNFOLD

HANDLES

WASHER

AND NUT

HARNESS CLIP, WASHER AND NUT

REMOVE & REINSTALL HARDWARE

FIGURE 2

STEP 5: Install roll bar protective structure:

A. Install side bars into frame brackets behind fuel tanks, making sure hinges on top of bars are facing toward rear of machine, and safety decals are facing forward and inward. See Figure 3. Secure each bar to its corresponding bracket with two 1/2-13 x 4-1/2” hex bolts and lock nuts. Do not tighten yet.

FIGURE 1

STEP 3: Install seat:

A.Check to make sure that there are two flat washers installed onto each of the four seat mounting studs and secured by a retaining ring. (If missing, replace with three standard 5/16 flat washers.)

NOTE: Seat must be in rearmost position during installation. Refer to Operator’s manual for seat adjustment procedures.

B.Install seat to seat plate, and secure each stud with one 5/16 flat washer and nyloc nut. See Figure 2. Tighten securely.

NOTE: Secure the harness clip to the left forward stud before installing the washer and nut. Slip the harness for the seat safety switch into this clip. See Figure 2.

SAFETY DECALS

FACING FORWARD

AND INWARD

AIR CLEANER CAP

ANTI-VIBRATION

BOLT

FIGURE 3

HINGES

FACING REARWARD

ATTACH TO FRAME BRACKET

STEP 4: Install rain cap onto engine air cleaner assembly, securing with supplied worm drive clamp. Tighten securely. See Figure 3.

INSTRUCTION No. 7100719 (Rev. 1, 7/7/2006) TP 300-5177-R1-HZ-N

1

Page 2
Page 1
Image 1
Snapper Zero Turning Z-Riding manual Instruction No Rev , 7/7/2006 TP 300-5177-R1-HZ-N
Page 2

Zero Turning Z-Riding specifications

The Snapper Zero Turn Z-Rider series is a robust and innovative solution for landscapers and homeowners looking for an efficient way to maintain their lawns and gardens. This line of zero-turn mowers is designed to navigate tight spaces with exceptional agility, allowing users to tackle a variety of mowing tasks with ease.

At the heart of the Snapper Zero Turn Z-Rider is its unique zero-turn technology. Unlike traditional riding mowers, which require wide turning arcs, the Z-Rider can pivot 180 degrees in place. This capability drastically reduces mowing time, especially in complex landscaping where obstacles, trees, and flower beds are present. The dual-lever steering system further enhances maneuverability, allowing the operator to seamlessly control speed and direction with just a touch of their fingers.

One of the standout features of the Snapper Zero Turn Z-Rider is its powerful engine options. Equipped with durable Briggs & Stratton or Kohler engines, these mowers deliver the performance needed for heavy-duty cutting tasks. Users can choose from various engine sizes to match their specific mowing needs, ensuring optimal power and efficiency. Coupled with a high-performance cutting deck, typically available in sizes ranging from 48 to 60 inches, the Z-Rider delivers a clean and even cut every time.

Technology plays a critical role in the design of the Snapper Zero Turn Z-Rider. The mowers feature a robust hydrostatic transmission that provides smooth speed control. This advanced transmission system allows for rapid acceleration and deceleration, making it easier to navigate various terrains. Additionally, the Z-Rider boasts an ergonomic design with adjustable seats and controls to enhance operator comfort during extended mowing sessions.

Durability is another key characteristic of the Snapper Zero Turn Z-Rider. The chassis is constructed from heavy-duty steel, providing a sturdy platform that can withstand the rigors of regular use. Furthermore, the mower is equipped with reinforced cutting decks that are built to last, reducing the need for frequent replacement or repairs.

Safety features are designed with the operator in mind. These include anti-tip technology and automatic brake systems, ensuring that the mower remains stable and secure during operation. The easy-access maintenance points simplify routine checks and upkeep, making it user-friendly for both novice and experienced operators.

Overall, the Snapper Zero Turn Z-Rider series combines cutting-edge technology, powerful performance, and robust durability, making it an ideal choice for anyone looking to achieve a beautifully manicured lawn with minimal effort. Whether for residential use or commercial landscaping, this mower is built to deliver results.
Top Page Image Contents