SONANCE CINEMA® SELECT
6. Tighten the four screws on the front of the speaker baffle. The RotoLock clamps will automatically rotate into position and begin clamping the speaker (Figure 11).
•When you notice resistance on the screws the speaker has been clamped successfully.
IMPORTANT: Always use
NOTE: THE SPEAKER FLANGE IS DESIGNED TO FLEX AND CONFORM TO ANY SMALL IMPERFEC- TIONS IN THE WALL SURFACE. DO NOT TIGHTEN THE SCREWS SO MUCH SO THAT THE FLANGE
7. Attach the | grille after the speaker | has been installed. Insert | about half | of | the grille into | the | groove |
at the edge of the speaker. Gently | fit the remaining half of | the grille | by | working around | the | speak- | |
er, fitting | the grille into the groove as you go. |
|
|
|
|
| |
NOTE: YOU | CAN ADJUST THE TORQUE APPLIED TO THE ROTOLOCK SCREWS TO ACHIEVE A | PROP- | |||||
ER GRILLE | FIT. |
|
|
|
|
|
|
PAINTING THE SPEAKERS AND GRILLES
You can paint the speakers and grilles before installing them, which will eliminate the “paint scar” that can be left on the wall if the speaker ever needs to be removed for service. You can also paint the speakers after installation, but before the grilles are attached. All Sonance Symphony speakers come from the factory fitted with a plastic ‘paint plug’ that protects the speaker drivers while the mounting flange is being painted.
RotoLock® |
|
Clamps |
|
F i g u r e | 1 1 : |
T i g h t e n i n g t h e R o t o L o c k C l a m p s |
Sonance always suggests painting the grille separately from the speaker. Before painting, carefully remove the
Spray the grille with thinned paint (5 parts thinner to 1 part paint), being careful not to plug the holes. Too heavy a coat of paint on the grille will adversely affect the sound of the speaker.
Once the grille and flange are painted and dry, replace the
SPECIFICATIONS
Cinema Select LCR |
|
| Cinema Select SUR |
|
|
|
Tweeter : | 1" (25mm) Silk dome, | Tweeter : | Two 1" (25mm) silk domes, | |||
| shielded magnet | Woofer : | 6½" (165mm) Carbon fiber cone, rubber | |||
Woofer : | 6½" (165mm) Carbon fiber cone, rubber |
| surround |
|
| |
| surround, shielded magnet | Frequency Response: | 55Hz – | 20kHz | ± 3dB | |
Frequency Response: | 80Hz – 20kHz | ±3dB | Impedance: | 8 Ohms nominal; 5 Ohms minimum | ||
Impedance: | 8 Ohms nominal; 5 Ohms minimum | Power Handling: | 5 watts minimum; 135 Watts maximum | |||
Power Handling: | 5 watts minimum; 135 Watts maximum | Sensitivity: | 90dB SPL (2.83V 1 meter) | |||
Sensitivity: | 90dB SPL (2.83V 1 meter) | Grille Material: | Perforated aluminum | |||
Grille Material: | Perforated aluminum | Adjustments: | None |
|
| |
Adjustments: | None |
| Dimensions (W x H x D): | 8¼” x 123/16" x 37/8" | ||
Dimensions (W x H x D): | 8¼” x 123/ " x 37/ " |
| (210mm | x 310mm x 98mm) | ||
| 16 | 8 |
|
|
|
|
| (210mm x 310mm x 98mm) | Cutout Dim. (W x H): | 613/16" x 1011/16" (172mm x 270mm) | |||
Cutout Dim. (W x H): | 613/16" x 1011/16" (172mm x 270mm) | Shipping Weight: | 10 lbs. (4.5kg) | Pair | ||
Shipping Weight: | 5 lbs. (2.3kg) | Each |
|
|
|
|
6