The Sound Advance® SA2C is a
The Sound Advance SA2C employs a flat rigid diaphragm, approximately
The SA2C’s exclusive installation methods, including the use of matching surface treatments, uniquely allows the speaker to be made truly invisible. This capability allows the loudspeaker system to be placed wherever optimal acoustics dictate, eliminating any visual concerns. The SA2C utilizes a 12dB per octave crossover centered at 2kHz, with both
Recommended Installations:
• Invisibly
Recommended Environment:
• Indoor or
Required Accessories:
•PBB4: 4" deep backbox for wall installation.
•PBB6: 6" deep backbox for ceiling installation.
(low frequency and high frequency)
Dimensions (H x W x D): 21" x 14" x 3" (534mm x 350mm x 76mm)
Product Weight: 7.7 lbs. (3.5kg) each
Shipping Weight: 16 lbs. (7.3kg) each, including finishing supplies and vellum overlay
Included Supplies: Vellum overlay, joint compound, overlay adhesive, measuring cup, rubber standoffs, screws, washers, hex key
Polar Response:
50dB 40dB 30dB 20dB | 10dB | 0dB | 0dB | 10dB | 20dB | 30dB 40dB 50dB | 50dB 40dB 30dB 20dB | 10dB | 0dB | 0dB | 10dB | 20dB | 30dB 40dB 50dB |
90° |
|
| 500Hz |
|
| 270° | 90° |
|
| 1kHz |
|
| 270° |
Recommended Accessories:
•ICC™ active electronic correction and response compensation processor
•Power Amplifiers such as Sonance® Sonamp® amplifiers with BBE® Sound Enhancement
Performance Specifications:
Radiating Surface: 294.0 in2 (1869.0cm2) Planar Diaphragm
60° |
|
| 300° |
30° |
| 330° | 500Hz |
| 0° |
| |
50dB 40dB 30dB 20dB 10dB 0dB | 2kHz | 0dB 10dB 20dB 30dB 40dB 50dB | |
90° |
| 270° | |
60° |
|
| 300° |
30° |
| 330° | 2kHz |
| 0° |
|
60° |
|
| 300° |
30° |
| 330° | 1kHz |
| 0° |
| |
50dB 40dB 30dB 20dB 10dB 0dB | 4kHz | 0dB 10dB 20dB 30dB 40dB 50dB | |
90° |
| 270° | |
60° |
|
| 300° |
30° |
| 330° | 4kHz |
| 0° |
|
Tweeter System: 0.82 lb (0.37 kg) Magnet with 1.02" (26mm) voice coil, 12dB/octave
Woofer System: 0.82 lb (0.37 kg) Magnet with 1.02" (26mm) voice coil; 12dB/octave
Frequency Response: 70Hz – 20kHz ±4dB
Power Rating: 60 Watts RMS as per EIA standard
Pressure Sensitivity: 90dB SPL @ 1 meter
System Impedance: 4 ohms nominal; 3.5 ohms minimum
Transformer: Primary Voltage — 70.7 Volts, Primary Taps — 0.5, 1, 2, 4, 8, 16, 32 Watts;
Dispersion: 140° hemispherical, up to 20kHz (see Polar Response graphs)
Finish: Primed surface ready to receive supplied vellum overlay
Overload Protection: Two independent
50dB 40dB 30dB 20dB 10dB 0dB | 8kHz | 0dB 10dB 20dB 30dB 40dB 50dB | 50dB 40dB 30dB | 20dB 10dB 0dB | 16kHz | 0dB 10dB 20dB 30dB 40dB 50dB | |
90° |
| 270° | 90° |
| 270° | ||
60° |
|
| 300° | 60° |
|
| 300° |
30° |
| 330° | 8kHz |
| 30° |
| 330° |
| 0° |
|
|
| 0° | 16kHz |
Warranty:
Sound Advance warrantees the SA2C to be free of any defect in material of workmanship for a period of 15 years. Should a properly- installed SA2C speaker fail, Sound Advance will replace the device at no charge, including shipping costs and labor for removal and reinstallation.
©2007 Sound Advance. All Rights Reserved. Sound Advance and Planar Diaphragm Technology are trademarks or registered trademarks of Dana Innovations. Specifications subject to change without notice. For the latest Sound Advance product information please go to www.soundadvance.com.
SA SOUND ADVANCE R | 212 Avenida Fabricante, San Clemente, CA 92672 |
TEL |