![](/images/new-backgrounds/1036561/365615x1.webp)
7.Insert the speaker into the hole in the wall.
Note: The RotoLock system can accommodate a maximum wall material thickness of 1¼”.
Step 7:
8.Tighten the four screws on the front of the speaker baffle. The RotoLock clamps will automatically rotate into position and begin clamping the speaker.
•When you notice resistance on the four screws the speaker has been clamped successfully.
The speaker flange is designed to flex and conform to any small imperfections in the wall surface. Do not tighten the screws so much so that the flange
Step 8: | Step 9: |
9.Attach the grille after the speaker has been installed. Insert about half of the grille into the groove at the edge of the speaker. Gently fit the remaining half of the grille by working around the speaker, fitting the grille into the groove as you go.
Note: You can adjust the torque applied to the RotoLock screws to achieve a proper grille fit.
IR Receiver Knockout
IR Knockout
Sonance Cinema Select LCR
speakers have a knockout for installing an IR receiver into
the speaker’s front baffle. This allows you to aim remote controls at the front of the room instead of at the electronics, in systems where
the electronics may be placed in an inconvenient location.
To remove the knockout, drill it out from the rear using a drill with a ½” bit (there is a sleeve guide directly behind the knockout).
After inserting the IR receiver through the hole, seal it into the speaker using silicone caulk (make sure that there are no gaps around the receiv- er that could create air leaks) and dress the wire into the groove on the back of the baffle.
Note: The speaker’s grille may reduce the effectiveness of the IR receiver. If this occurs, slightly enlarge the holes in the grille that are directly in
front of the IR receiver.
PAINTING THE SPEAKERS AND GRILLES
You can paint the speakers and grilles before installing them, which will eliminate the “paint scar” if the speaker ever needs to be removed for service. You can also paint the speakers after installation, but before the grilles are attached. Sonance Cinema Select speakers come from the factory fitted with a plastic ‘paint plug’. Use the paint plug to protect the speaker drivers while the flange is being painted along with the wall.
Sonance always suggests painting the grille separately from the speaker. Before painting,carefully remove the
Spray the grilles with thinned paint (5 parts thinner to 1 part paint), being careful not to plug the holes. Too heavy a coat of paint on the grille will adversely affect the sound of the speaker.
Once the grilles and flange are painted and dry, replace the
SPECIFICATIONS
Cinema Select LCR
Tweeter | 1" (25mm) Silk dome, |
Woofer | 6½" (165mm) Carbon fiber cone, rubber surround, |
| shielded magnet |
Frequency Response | 80Hz – 20kHz ±3dB |
Impedance | 8 Ohms nominal; 5 Ohms minimum |
Power Handling | 5 watts minimum; 135 watts maximum |
Sensitivity | 90dB SPL (2.83V 1 meter) |
Grille Material | Perforated aluminum |
Adjustments | None |
Dimensions (W x H x D) 8¼" x 123/16" x 33/8" (210mm x 310mm x 86mm) | |
Cutout Dim. (W x H) | 67/8" x 10¾" (175mm x 273mm) |
Shipping Weight | 5 lbs. (2.3 KG) each |
Cinema Select SUR
Tweeter | Two 1" (25mm) Silk dome, |
Woofer | 6½" (165mm) Carbon fiber cone, rubber surround |
Frequency Response | 80Hz – 20kHz ±3dB |
Impedance | 8 Ohms nominal; 7 Ohms minimum |
Power Handling | 5 watts minimum; 135 watts maximum |
Sensitivity | 90dB SPL (2.83V 1 meter) |
Grille Material | Perforated aluminum |
Adjustments | None |
Dimensions (W x H x D) 8¼" x 123/16" x 33/8" (210mm x 310mm x 86mm)
Cutout Dim. (W x H) | 67/8" x 10¾" (175mm x 273mm) |
Shipping Weight | 10 lbs. (4.5 KG) Pair |
3