Sony BKP-7933 Section 1 Installation

1-1 (E)

BKP-7933

Section 1Installation

1-1. Checking ROM Version

When the BKP-7933 is installed in the CNU-700, be sure to check that the ROM versions for IC4 and

IC5/AT-89 board of the CNU-700 are Ver. 3.00 or higher. If the ROM needs to be replaced, contact your

local Sony Sales Office/Service Center.

ROM Version

IC4/AT-89 board Ver. 3.00 or higher

IC5/AT-89 board Ver. 3.00 or higher

1-2. Configuration of BKP-7933

The BKP-7933 is composed of the following items.

. Main board (IF-689 board) (1)

.Rear panel (with CN-1558 board) (1)

.Installation manual (1)

1-3. Installation Procedure

This section explains briefly on installation procedures. Refer to each section for details.

Installation procedure Section

1. Checking ROM Version 1-1. Checking ROM Version

2. Switch setting on the board 1-4. Setting Switches on the IF-689 Board

3. Installation of the IF-689 board/Rear panel 1-5. Installation

4. Connection 1-6. Connection

5. Setup 1-7. Setting Up

1-9. Modification of RCP

1-10.Using the BKP-7933 in the HD System

6. Data Backup/Restore 1-8. Data Backup/Restore

Contents

Main Page Table of Contents Manual Structure 1. Installation Page Manual Structure Purpose of this manual Relative manuals Trademarks Page Section 1 Installation 1-1. Checking ROM Version 1-2. Configuration of BKP-7933 1-3. Installation Procedure 1-4. Setting Switches on the IF-689 Board Page 1-5. Installation 1-5-1. Installing the IF-689 Board 1-5-2. Installing the Rear Panel 1-6 (E) 1-6. Connection 1-6-1. Connection Connector/Cable 1-7 (E) 1-6-2. Connector Input/Output Signals REMOTE S-BUS BNC 75 Z, 1.0 Vp-p I/O PORT (D-sub 50P, Female) 1-6-3. Notes on Connection 1-6-4. Instance of System Configuration 1-9 (E) 1-7. Setting Up 1-7-1. Outline Page 1-12 (E) 1-7-2. Linking the RCP Assignment and VE Monitor Selection 1-7. Setting Up CCU-700A Digital Video Routing SwitcherBVP-500/700/900 series RCP-700 series 1-13 (E) Page 1-15 (E) 1-7. Setting Up 1-7-3. Linking the MSU Camera Selection and the VE Monitor Selection CCU-700ABVP-500/700/900 series Digital Video Routing Switcher MSU-700 1-16 (E) Page 1-18 (E) 1-7-4. Switching the Video on the Preview Monitor with the RCP PREVIEW Switch Page Page Page 1-7-5. Executing RCP Assignment from Equipment Other Than MSU 1-23 (E) Page 1-25 (E) 1-7-6. Switching the MSU Camera Selection Externally Page 1-7-7. Changing the Camera Assignment Virtually Page 1-7-8. Using the Tally System Page Page 1-7-9. Displaying the Self-diagnostic Information on the Terminal 1-7-10. Returning the Setups of the MODIFICATION COMMAND to the Factory Default Values 1-7-11. Returning the Setups of the MAINTENANCE COMMAND to the Factory Default Values 1-34 (E) 1-7-12. Connecting 13 or More Cameras 1-8. Data Backup/Restore 1-8-1. Installing the BZR-10 1-8-2. Data Backup (Uploading) Page 1-8-3. Data Restore (Downloading) 1-9. Modification of RCP 1-9-1. Checking ROM Version 1-9-2. Modification of RCP-700/701 Page 1-9-3. Modification of RCP-720 1-9-4. Modification of RCP-721 1-9-5. Modification of RCP-730/731 1-44 (E) 1-10. Using the BKP-7933 in the HD System 1-10-1. Controlling the Routing Switcher via the RS-422A Interface Page 1-10-2. Controlling a Waveform Monitor 1-47 (E) 1-10. Using the BKP-7933 in the HD System (WIRING SIDE) A/B RECALL 0 1-11. Description on Internal Indicators (Component side/A side) IF-689 board IF