Operating Instructions
Owner’s Record
WARNING
WARNING
IMPORTANT
ATTENTION
Getting Started
Overview
Adjusting and Setting With Menus
Operation Using the Supplied
Remote Commander
Installation and Connections
Appendix
Getting Started
Overview
Supplied Components and Accessories
Camera (1)
AC power adaptor MPA-AC1(Sony) (1)
AC power cord (1)
Remote commander (1)
Optional Products
BRU-300/300POptical Multiplex Unit
CCFC-M100Optical Fiber Cable
This is a 2-core multi-modeoptical fiber cable of 100 m (328 feet) long
Supplied accessories: extension plug
BRBK-302SDI Card
BRBK-303Optical Multiplex Card
Video Switcher (commercially available)
Operating a BRC-300/300PCamera Using the Supplied Remote Commander
This system allows you:
To operate the camera readily from a short distance
System configuration
Operating a BRC-300/300PCamera Using the RM-BR300Remote Control Unit
Operating Multiple BRC-300/300PCameras Using the RM-BR300Remote Control Unit
Operating a BRC-300/300PCamera from a Long Distance
Operating Multiple BRC-300/300PCameras from a Long Distance
Using BRC-300/300PCameras and VISCA-controllableCameras in the Same System
Camera
Front
ALens
BTally lamp
CRemote sensor
MVISCA RS-232CIN connector
NVISCA RS-232COUT connector
ODC IN 12V connector
Connect the supplied AC power adaptor
PCard slot
Remote Commander (supplied)
ACAMERA SELECT buttons
BFOCUS buttons
Used for focus adjustment
CDATA SCREEN button
RM-BR300Remote Control Unit (not supplied)
ALOCK button and indicator
BVALUE/R control
CBRIGHT/B control
DMODE button
HRESET button
IPRESET button
JPANEL LIGHT button
KBACK LIGHT button
LPAN-TILTRESET button
Rear/Bottom
UMODE selector
Use position 1 to 4 when all the connected cameras are of the same model
VVISCA RS-232Cconnector
WVISCA RS-422connector
BRU-300/300POptical Multiplex Unit (not supplied)
APower switch
BPower indicator
Lit in green:
Lit in red:
BRBK-301Analog RGB Component Card (not supplied)
ARGB/SYNC connector
BRBK-302SDI Card (not supplied)
ASDI connector
BRBK-303Optical Multiplex Card (not supplied)
Setting Menus
displayed
For the overall menu configurations, see page
You cannot perform pan/tilt and zoom operations while the menu is displayed
Main Menu
Menu Operation Using the Supplied Remote Commander
2,4
To return to the main menu
To return to the normal display
Menu Operation Using the RM- BR300 Remote Control Unit
The EXPOSURE menu is used to set the items regarding the exposure
MODE (exposure mode)
FULL AUTO:
MANUAL:
SHUTTER Pri:
The FOCUS menu is used to select the focus mode
AUTO FOCUS (automatic focus)
NORMAL: The automatic focus adjustment is always activated
INTERVAL:
ZOOM Trig:
The PAN TILT ZOOM menu is used to select the pan/ tilt/zoom mode
PAN-TILTLIMIT
You can select the following values:
PAN LEFT:
PAN RIGHT:
EFFECT (picture effect)
OFF: No picture effect
NEG: The image of the camera is reversed to negative
B&W: The image of the camera becomes monochrome
WIDE (wide mode)
DISPLAY INFO
Operation Using the Supplied Remote Commander
For details, see “Installation” (page 42) and “Connections” (page 46)
2 Turn on the peripheral devices
To turn on/off the camera using the Remote Commander
1 Press the POWER switch
Operating Multiple Cameras with the Remote Commander
IR SELECT
To focus the camera on a subject automatically
To focus the camera on a subject manually
For details of the camera settings to be preset, see “Presetting Items” on page
To cancel the preset memory
1 Press the PAN-TILTRESET button to reset the pan/ tilt position
To recall the stored settings
Operation Using the RM-BR300Remote Control Unit
Operating Multiple Cameras
To assign camera addresses automatically
To assign camera addresses manually
1 Turn on the power of the camera and the RM- BR300 Remote Control Unit
The camera will turn on, performing the pan/tilt reset action automatically
2 Press the CAMERA button corresponding to the camera you want to operate
Release the joystick to stop panning/tilting
To reset the pan/tilt position, press the PAN-TILTRESET button
Turn the dial on the upper part of the joystick
Adjusting the White Balance
To adjust the white balance automatically
To adjust the white balance manually
Adjusting the Brightness
1Press the PAN-TILTRESET button to reset the pan/ tilt position
Press the CAMERA button to select the camera whose settings you want to preset
Adjust the position, zooming, focusing and backlighting of the camera. (See
The settings are stored in the memory of the camera
Setting the Speed of the Camera Moving to a Preset Position
Installation and Connections
To attach the camera to a tripod
The tripod must be set up on a flat surface and tightened firmly by hand
Use a tripod with screws meeting either of the following specifications
To attach a wide conversion lens
Installing the Camera on the Ceiling
•Be sure to attach the supplied wire rope to prevent the camera from falling
Before installation
Installation
Page
Connecting to an AC Outlet
To remove the camera
Connecting the RM-BR300Remote Control Unit
Use the RS-232Cconnecting cable supplied with the Remote Control Unit
To connect the Remote Control Unit using the VISCA RS-422connectors
For the use of the RS-422connector plugs, see page
When the connections using the VISCA
Connecting a Video Monitor, VTR
Connecting a Device Equipped with VISCA RS-232CConnector
Connecting a Device Equipped with VISCA RS-422Connector
Do not make the VISCA
Connecting a Video Monitor Equipped with Analog RGB/ Component Connectors
Connecting the BRU-300/300POptical Multiplex Unit
Notes on use of the CCFC-M100Optical Fiber Cable
Connecting a Video Switcher
Connecting a Sync Signal Generator
To connect a single camera
To connect multiple cameras
You can connect up to seven cameras
Appendix
Page
Page
The menus of the camera are configured as described below
The initial settings of each item are in bold
(page 26)
(page 27)
(page 28)
(page 29)
(page 30)
The following setting items can be stored in the memory of the camera
Presetting menu items
System
Input/output connectors
General
Supplied accessories
Dimensions
BRC-300/300PVideo Camera
Top
Side
Side
Page
VISCA RS-232COUT
IN VISCA RS-232C
OUT
VISCA RS-422
RXD OUT –
RXD OUT +
TXD OUT –
TXD OUT +
RXD IN –
Using the VISCA RS-422Connector Plug
To remove the connector plug