Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION

23.2watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.

CEA2006 Standard

Power Output: 17 Watts RMS ⋅ 4 at 4 Ohms < 1% THD+N

SN Ratio: 82 dBA

(reference: 1 Watt into 4 Ohms)

CD Player section

Signal-to-noise ratio: 120 dB

Frequency response: 10 – 20,000 Hz

Wow and flutter: Below measurable limit

Tuner section

FM

Tuning range: 87.5 – 107.9 MHz

Antenna terminal: External antenna connector

Intermediate frequency: 10.7 MHz/450 kHz

Usable sensitivity: 9 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz: 0.5 % (stereo),

0.3% (mono) Separation: 35 dB at 1 kHz Frequency response: 30 – 15,000 Hz

AM

Tuning range: 530 – 1,710 kHz

Antenna terminal: External antenna connector

Intermediate frequency: 10.7 MHz/450 kHz

Sensitivity: 30 µV

Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 52 W ⋅ 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (sub/rear switchable) Power antenna relay control terminal Power amplifier control terminal

Inputs:

Antenna input terminal

AUX input jack (stereo mini jack)

Tone controls:

Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD) Power requirements: 12 V DC car battery

(negative ground)

Dimensions: Approx. 178 ⋅ 50 ⋅ 179 mm (7 1/8 ⋅ 2 ⋅ 7 1/8 in) (w/h/d)

Mounting dimensions: Approx. 182 ⋅ 53 ⋅ 161 mm

Mass: Approx. 1.2 kg (2 lb 11 oz)

Supplied accessories:

Card remote commander: RM-X151 (CDX-GT200 only)

Parts for installation and connections (1 set)

Optional accessory:

Card remote commander: RM-X114 (CDX-GT20W only)

Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information.

US and foreign patents licensed from Dolby Laboratories.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

Design and specifications are subject to change without notice.

•Lead-free solder is used for soldering certain parts. (more than 80 %)

•Halogenated flame retardants are not used in the certain printed wiring boards.

•Halogenated flame retardants are not used in cabinets.

•Packaging cushions do not use polystyrene foam.

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.

General

No power is being supplied to the unit.

•Check the connection. If everything is in order, check the fuse.

•If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit.

The power antenna does not extend. The power antenna does not have a relay box.

No sound.

•The volume is too low.

•The ATT function is activated.

•The position of the fader control “FAD” is not set for a 2-speaker system.

No beep sound.

•The beep sound is canceled (page 9).

•An optional power amplifier is connected and you are not using the built-in amplifier.

14

(7 1/4 ⋅ 2 1/8 ⋅ 6 3/8 in) (w/h/d)