Specifications

CD Player section

Signal-to-noise ratio: 120 dB

Frequency response: 10 – 20,000 Hz

Wow and flutter: Below measurable limit

Tuner section

FM

Tuning range: 87.5 – 108.0 MHz

Aerial terminal: External aerial connector

Intermediate frequency: 10.7 MHz/450 kHz

Usable sensitivity: 9 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz: 0.5 % (stereo),

0.3% (mono) Separation: 35 dB at 1 kHz Frequency response: 30 – 15,000 Hz

MW/LW

Tuning range:

MW: 531 - 1,602 kHz

LW: 153 - 279 kHz

Aerial terminal: External aerial connector

Intermediate frequency: 10.7 MHz/450 kHz

Sensitivity: 30 µV

Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 50 W ⋅ 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (sub/rear switchable) Power aerial relay control terminal

Power amplifier control terminal

Inputs:

Aerial input terminal

AUX input jack (stereo mini jack)

Tone controls:

Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD) Power requirements: 12 V DC car battery

(negative earth)

Dimensions: Approx. 178 ⋅ 50 ⋅ 179 mm (w/h/d)

Mounting dimensions: Approx. 182 ⋅ 53 ⋅ 161 mm (w/h/d)

Mass: Approx. 1.2 kg

Supplied accessory:

Parts for installation and connections (1 set)

Optional accessory:

Card remote commander: RM-X114

Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information.

US and foreign patents licensed from Dolby Laboratories.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

Design and specifications are subject to change without notice.

•Lead-free solder is used for soldering certain parts. (more than 80 %)

•Halogenated flame retardants are not used in the certain printed wiring boards.

•Halogenated flame retardants are not used in cabinets.

•VOC (Volatile Organic Compound)-free vegetable oil based ink is used for printing the carton.

•Packaging cushions do not use polystyrene foam.

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.

General

No power is being supplied to the unit.

•Check the connection. If everything is in order, check the fuse.

•If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit.

The power aerial does not extend. The power aerial does not have a relay box.

No sound.

•The volume is too low.

•The ATT function is activated.

•The position of the fader control “FAD” is not set for a 2-speaker system.

No beep sound.

•The beep sound is cancelled (page 7).

•An optional power amplifier is connected and you are not using the built-in amplifier.

The contents of the memory have been erased.

•The RESET button has been pressed. t Store again into the memory.

•The power connecting lead or battery has been disconnected.

•The power connecting lead is not connected properly.

Stored stations and correct time are erased. The fuse has blown.

Makes noise when the position of the ignition key is switched.

The leads are not matched correctly with the car’s accessory power connector.

12