Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 45 W ⋅ 4 (at 4 ohms)

General

Output:

Power antenna (aerial) relay control terminal

Inputs:

Telephone ATT control terminal

Antenna (aerial) input terminal

AUX input jack (stereo mini jack)

Tone controls:

Low: ±10 dB at 100 Hz

High: ±10 dB at 10 kHz

Loudness:

+9 dB at 100 Hz

+5 dB at 10 kHz

Power requirements: 12 V DC car battery (negative ground (earth))

Dimensions: Approx. 178 ⋅ 50 ⋅ 179 mm (7 1/8 ⋅ 2 ⋅ 7 1/8 in) (w/h/d)

Mounting dimensions: Approx. 182 ⋅ 53 ⋅ 162 mm (7 1/4 ⋅ 2 1/8 ⋅ 6 1/2 in) (w/h/d)

Mass: Approx. 1.2 kg (2 lb 11 oz)

Supplied accessory:

Parts for installation and connections (1 set)

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

Design and specifications are subject to change without notice.

•Halogenated flame retardants are not used in the certain printed wiring boards.

•Halogenated flame retardants are not used in cabinets.

•Paper is used for the packaging cushions.

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.

General

No power is being supplied to the unit.

Check the connection. If everything is in order, check the fuse.

The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box.

No sound.

•The volume is too low.

•The position of the fader control “FAD” is not set for a 2-speaker system.

No beep sound.

The beep sound is canceled (page 10).

The contents of the memory have been erased.

•The power supply lead or battery has been disconnected.

•The power supply lead is not connected properly.

Stored stations and correct time are erased. The fuse has blown.

Makes noise when the position of the ignition is switched.

The leads are not matched correctly with the car’s accessory power connector.

The display disappears from/does not appear in the display window.

•The dimmer is set “DIM-ON” (page 10).

•The display disappears if you press and hold (OFF). tPress and hold (OFF) on the unit until the

display appears.

•The connectors are dirty (page 13).

The Auto Off function does not operate.

The unit is turned on. The Auto Off function activates after turning off the unit.

tTurn off the unit.

CD playback

The disc cannot be loaded.

•Another disc is already loaded.

•The disc has been forcibly inserted upside down or in the wrong way.

The disc does not playback.

•Defective or dirty disc.

•The CD-Rs/CD-RWs are not for audio use (page 12).

MP3/WMA files cannot be played back.

The disc is incompatible with the MP3/WMA format and version (page 12).

MP3/WMA files take longer to play back than others.

The following discs take a longer time to start playback.

–a disc recorded with a complicated tree structure.

–a disc recorded in Multi Session.

–a disc to which data can be added.

The display items do not scroll.

•For discs with very many characters, those may not scroll.

•“A.SCRL” is set to “OFF”.

tSet “A.SCRL-ON” (page 10).

The sound skips.

• Installation is not correct.

tInstall the unit at an angle of less than 45° in a sturdy part of the car.

•Defective or dirty disc.

The disc will not eject.

Press Z (eject) (page 6).

14