Wireless Keypad
Clavier sans fil
Instruction Manual / Mode d’emploi
CECHZK1UC |
US
WARNING
This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and
This transmitter must not be
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
−Reorient or relocate the receiving antenna.
−Increase the separation between the equipment and receiver.
−Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
−Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
If you have questions about this product, call our technical support line at
Consumer Services/Technical Support
PO Box 5888, San Mateo, CA 94402-0888 U.S.A
| Declaration of Conformity |
Trade Name : | SONY |
Model No. : | CECHZK1UC |
Responsible Party : Sony Electronics Inc.
Address : | 16530 Via Esprillo, San Diego, CA 92127 U.S.A. |
Telephone No. : |
This device complies with Part 15 of the FCC Rules and
(2)this device must accept any interference received, including interference that may cause undesired operation of this device.
This Class B digital apparatus complies with Canadian ICES-003.
Warning
If you come into contact with material from a leaking battery, take the following actions:
–If the material gets into the eyes, do not rub. Immediately flush the eyes with clean water and seek medical attention.
–If the material comes into contact with the skin or clothes, immediately rinse the affected area with clean water. Consult your physician if inflammation or soreness develops.
Avoid prolonged use of this product. Take a break at about 30 minute intervals.
Stop using this unit immediately if you begin to feel tired or if you experience discomfort or pain in your hands, wrists or arms during use.
If the condition persists, discontinue use and consult a doctor.
This product is intended for use with the hands only.
Do not allow the battery to come into contact with fire or subject it to extreme temperatures such as in direct sunlight, in a vehicle exposed to the sun or near a heat source.
Caution
Be careful not to pinch your fingers with the clamp when attaching/detaching the wireless keypad to/ from the wireless controller.
When disposing of the keypad, carefully follow the precautions listed below:
−When removing the battery, do so in a location out of the reach of small children to help prevent accidental swallowing of small parts such as screws.
−Be careful not to hurt your nails or fingers when removing the battery.
Part names
Blue button | Orange button | |
Status indicator | POWER switch | |
| ||
Caps lock indicator |
| |
| Directional keys | |
Touch pad indicator | START button* | |
SELECT button* | ||
| ||
| PS button* |
* These buttons can only be used when the keypad is attached to a wireless controller.
USB connector ClampPreparing for use
Checking the version of the PS3™ system software
To use the wireless keypad, the PS3™ system software must be version 2.50 or later. You can
check the system software version by selecting (Settings) (System Settings) "System Information" on the XMB™ screen of the PS3™ system.
Pairing the wireless keypad and the PS3™ system
Before using the wireless keypad, you must first register or "pair" the keypad and the PS3™ system. You only need to do this the first time you use the keypad.
1 Turn on the PS3™ system.
2 Slide the power switch of the keypad to "ON".
3 Connect the keypad to the PS3™ system using a USB cable.
The keypad is now paired with the PS3™ system.
USB cableCheck that the system is turned on (power indicator is lit solid green).HintA USB cable is not included. Use the USB cable supplied with the PS3™ system or any Type A -
Turning the wireless keypad on and off
Slide the power switch to "ON" to place the wireless keypad in standby mode. When you press any character key, the status indicator will light up to indicate that the keypad is ready to use. To turn off the keypad, slide the power switch to "OFF".
Hint
If the keypad is not used for a period of time (with the power on), it will switch to standby mode and the status indicator will turn off.
Attaching the wireless keypad to a wireless controller
When using the wireless keypad with the PS3™ system, you must attach it to a wireless controller.
Open the clamp.
Place the wireless keypad over the wireless controller as shown in the diagram, and then press down firmly to attach the keypad to the controller.
Detaching the wireless keypad
Open the clamp, and then carefully pull up on the wireless keypad.
Charging the wireless keypad
To charge the wireless keypad battery, check that the PS3™ system is turned on (power indicator is lit solid green), and then connect the keypad to the system using a USB cable. While charging the battery, the status indicator, the Caps lock indicator and the touch pad indicator will all flash. When charging is complete, these indicators will turn off.
HintsThe wireless controller is not charged during the process of charging the keypad.
The battery has a limited life span. Battery charge duration will gradually decrease with repeated usage and age. Battery life also varies depending on the storage method, usage state, environment and other factors.
If the keypad is charged during use, the status indicator will flash. When charging is complete, the status indicator will stop flashing.
Entering text
You can enter text in the same way as with a standard PC keyboard. To enter an uppercase letter, first press the Shift key. To enter keypad characters that are colored blue or orange, first press the corresponding blue or orange button. To enter an accented letter, first enter the accent and then enter the letter.
This character is entered when | This character is entered when |
the blue button is pressed. | the orange button is pressed. |
When the Shift key is pressed, uppercase letters (instead of lowercase letters) can be entered.
Hint
To continue to enter keypad characters colored blue or orange, you must press the orange or blue button before each character you enter.
Commonly used keys
| Enters a tab |
Orange button + | Turns on caps lock |
Confirms characters that have been typed but not entered
Blue button + | Inserts a line break |
| Moves the cursor left and right |
Blue button + | Moves the cursor up and down |
| Inserts a space |
| Displays the message box of the PS3™ system |
Switches to touch pad mode
Displays the Friends list
Using touch pad mode
When in touch pad mode, the wireless keypad can be used like a mouse. You can use touch pad mode for cursor control in the browser. Move your finger over the area used as a touch pad. When you press the touch pad button, the touch pad indicator will light up and the keypad will switch to touch pad mode.
The area that can be used as a touch pad The pointer moves as you move your finger.These keys operate in the same way as the left/right buttons on a mouse.Touch pad buttonCalibrating the wireless keypad for touch pad mode
Before using touch pad mode for the first time, you must calibrate the keypad. To calibrate the keypad, switch it to touch pad mode, and then press and hold down the orange and blue buttons at the same time for at least two seconds. The calibration is complete when the touch pad indicator flashes once. Do not touch the touch pad area or turn off the keypad during calibration.
Hint
You cannot enter text when the keypad is in touch pad mode. To enter text, press the touch pad button again.
Using the wireless keypad with other products
You can pair and use the wireless keypad with other
Hints
The keypad is not guaranteed to work with all
A USB cable can be used to pair the keypad and the PS3™ system only.
When the keypad is paired with another
When disposing of the wireless keypad
When disposing of the wireless keypad, remove the battery and follow local regulations regarding disposing of batteries.
Notice
Other than when disposing of the keypad, never remove the screws and never remove the battery from the keypad.
1 Using a crosshead screwdriver, remove the screws from the keypad rear (8 places) and carefully remove the casing.
2 Unplug the connector, and then remove the battery.
BatteryConnectorRecycling Lithium-Ion Batteries
Lithium-Ion batteries are recyclable.
You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.
For more information regarding recycling of rechargeable batteries, call toll free