Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HT-7100DH 5:Preparing the receiver and the remote, 27US, Started Getting, 3 Press MEMORY/ENTER, 2 Hold down ?/1 for 5 seconds, 1 Press ?/1 to turn off the receiver

1 84

Download 84 pages, 3.41 Mb

5:Preparing the receiver and the remote

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

AC power cord

CENTER

To the wall outlet

Performing initial setup operations

Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults.

Be sure to use the buttons on the receiver for this operation.

1,2

? / 1

MASTER VOLUME

INPUT SELECTOR

3

1 Press ?/1 to turn off the receiver.2 Hold down ?/1 for 5 seconds.

“PUSH” and “ENTER” appears on the display alternately.

3 Press MEMORY/ENTER.

After “CLEARING” appears on the display for a while, “CLEARED” appears.

The following items are reset to their factory settings.

•All settings in the LEVEL, TONE, SUR, TUNER, AUDIO, VIDEO and SYSTEM menus.

•The sound field memorized for each input and preset station.

•All sound field parameters.

•All preset stations.

•All index names for inputs and preset stations.

•MASTER VOLUME is set to “VOL MIN”.

•Input is set to “DVD”.

27US

Started Getting

Contents

Page WARNING For customers in the United States –Reorient or relocate the receiving antenna –Increase the separation between the equipment and receiver –Consult the dealer or an experienced radio/TV technician for help •The instructions in this manual are for model HT-7100DH The HT-7100DHconsists of: • Receiver STR-K7100 • DVD player Table of Contents Description and location of parts KINPUT SELECTOR LMOVIE MA.F.D N2CH About the indicators on the display LFE ;PL OPT DTS SP B Name Function LCOAX is set to “AUTO IN” and the being input through the COAXIAL jack, or when Rear panel ADIGITAL INPUT/OUTPUT section OPTICAL IN jack player, etc. The EAUDIO INPUT/OUTPUT section FANTENNA section RM-AAP016 10US A AV ?/1 (on/standby) video components that the remote is programmed to operate If you press ?/1 (B) at the KOPTIONS Press to display and select items OPTIONS TOOLS TV, press TV (Z) and then press OPTIONS TOOLS DISC SKIP SCATEGORY Press to select the category for XM Radio REPLAY ADVANCE 1: Installing speakers You can install your surround speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws 15US 2: Connecting speakers 3a: Connecting the audio components 3b: Connecting the video components AAudio cord (not supplied) BVideo cord (not supplied) CComponent video cord (not supplied) Tips –connect the audio output jacks of the TV to the TV IN jack of the receiver –turn off or mute the TV’s volume The following illustration shows how to connect a DVD player/DVD recorder Connecting a DVD player •Do not bend or tie the optical digital cords All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies AA BB C AHDMI cable (not supplied) BCoaxial digital cord (supplied) COptical digital cord (not supplied) 22US If you connect a Blu-raydisc player Notes on HDMI connections Notes on digital audio signals connection 23US •Do not bend or tie optical digital cords BOptical digital cord (not supplied) CVideo cord (not supplied) 24US Connecting components with analog video and audio jack CAudio/video cord (not supplied) 25US 4: Connecting the antennas 5:Preparing the receiver and the remote 1 Press ?/1 to turn off the receiver 2 Hold down ?/1 for 5 seconds 3 Press MEMORY/ENTER 27US 6:Selecting the speaker system 7:Calibrating the appropriate settings automatically •Check the connection between each speaker and the receiver •Adjust the speaker level •Measure the distance of each speaker to your listening position Press AUTO CAL The measurement process will take a few minutes to complete The table below shows the display when measurement starts Measurement for Display Error codes To rectify the error Error codes and remedies Warning codes 31US To change the settings manually 1Record down the warning code 5Follow the solution provided in the “Warning codes and solutions” below Warning codes and solutions Warning 3-6 Gg Selecting a component To avoid damaging your speakers Before you turn off the receiver, be sure to turn down the volume level To listen to the sub woofer 1Press POWER The POWER indicator lights up Listening/Watching a component •Refer to the operating instructions supplied with the TV and DVD player •Check the following if you cannot listen to multi channel sound –Be sure the digital audio output of the DVD player is set up properly You can select the sound field to suit the movie/music. Refer to Music: CONCERT Navigating through menus 3-7 Gg Menu Parameters Settings Initial setting 40US Adjusting the level Adjusting the tone Settings for the surround sound Settings for the tuner Settings for the audio Settings for the video Settings for the system xSUR POS (Surround speaker position) •SIDE/LO •SIDE/HI •BEHD/LO Enjoying Dolby Digital and DTS Surround sound Press A.F.D. repeatedly to select the sound field you want For details, see “Types of A.F.D. mode” (page 48) Sound Surround Enjoying 47US Types of A.F.D. mode Decoding A.F.D. mode Multi channel Effect Selecting a preprogrammed sound field 49US Types of sound field available Sound field for Movie CINEMA STUDIO EX A Using only the front speakers and sub woofer Press 2CH 51US 2 While holding down 2CH, press ?/1 Listening to FM/AM radio 1 Press TUNER repeatedly to select the FM or AM band 2 Press TUNING + or TUNING – The receiver stops scanning whenever a station is received Using the controls on the receiver 1Turn INPUT SELECTOR to select the FM or AM band Presetting radio stations 5-8 Gg Listening to the XM Radio 1 Press TUNER repeatedly to select “XM RADIO” 2 Press TUNING + or TUNING – to select channel 57US 3 Check the XM Radio ID on the display and write it in the space provided here Display Description 1 Press TUNER repeatedly to select the “XM RADIO” 2 Press TUNING + or TUNING – to select a channel Selecting channels from a category (CATEGORY TUNING) 2 Press CATEGORY MODE repeatedly to select “ONE CAT” 3 Press CATEGORY + or CATEGORY – to select the category you want 4 Press TUNING + or TUNING – to select the channel Selecting channels by inputting the channel number directly Presetting XM Radio stations 2 Tune in the channel you want to preset For details on selecting channels, see “Listening to the XM Radio” (page 56) 4 Press the numeric buttons to enter the preset number 6 Repeat steps 2 to 5 to preset another channel 2 Press PRESET + or PRESET – repeatedly to select the preset channel you want XM Radio messages list Message appears The XM antenna is not Make sure that the antenna is securely connected Switching the audio input mode AVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Press and hold both sides of the connector and then pull out the connector 64US Notes 1 Press DMPORT You can also use the INPUT SELECTOR on the receiver to select “DMPORT” Initial setting: –NONE The assignable composite video input are VIDEO 1, VIDEO 3, DVD and SAT inputs 2 Start playback of the connected component Listening to digital sound from other inputs 3 Press V/v repeatedly to select “5-AUDIO” 5 Press V/v repeatedly to select “D.ASSIGN” 8 Press or b to enter your selection 66US Naming inputs Changing the display Using the Sleep Timer Recording using the receiver Press RM SET UP The RM SET UP indicator slowly flashes Programming the remote 2 Press the input button for the component you want to control 5 Repeat steps 1 to 4 to control other components •The indicator turns off while a valid button is pressed •For the numeric codes, only the last three numbers entered are valid If programming is unsuccessful, check the following: To clear the memory of the remote While holding down MASTER VOL –,press and hold ?/1 and then press AV ?/1 The indicator flashes 3 times, then goes off The numeric codes corresponding to the component and the maker of the component To control an LD player 601, 602 To control a video CD player MakerCode(s) SONY605 To control a TV 73US To control a satellite tuner To control a cable box To control a tuner To control a Blu-raydisc recorder To control a PSX Glossary Precautions Troubleshooting There is no sound from one of the front speakers There is no sound from analog 2 channel sources There is no sound from digital sources (from COAXIAL or OPTICAL input jack) Check that the INPUT MODE is not set to “ANALOG” •Check the HDMI connection Dolby Digital or DTS multi channel sound is not reproduced The MULTI CHANNNEL DECODING lamp does not light up in blue Recording cannot be carried out •Check that the components are connected correctly •Select the source component using the input buttons Radio stations cannot be tuned in Remote control The remote does not function •Point the remote at the remote sensor on the receiver •Remove any obstacles in the path between the remote and the receiver Specifications Power consumption Speaker section •Front speakers (SS-MSP7000) •Center speaker (SS-CNP900) •Surround speakers (SS-SRP7000) Index Sony Corporation