Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HT-7100DH Specifications, 81US, General, Area code, Area code, AUDIO POWER, Video section, SPECIFICATIONS, FM tuner section, AM tuner section, Amplifier section

1 84

Download 84 pages, 3.41 Mb

Specifications

AUDIO POWERSPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONIC DISTORTION:

With 6 ohm loads, both channels driven, from 120 – 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milliwatts to rated output.

Amplifier section

Power Output1)

Models of area code U

Stereo mode (rated)

(6 ohms 1 kHz, THD 1%)

90 W + 90 W

Surround mode (reference) (6 ohms 1 kHz, THD 10%)

RMS Output2) FRONT: 140 W/ch CENTER: 140 W SURROUND: 140 W/ch

1)Measured under the following conditions:

Area code	Power requirements
U	120 V AC, 60 Hz

2)Reference power output for front, center and surround speakers. Depending on the sound field settings and the source, there may be no sound output.

Inputs

Analog	Sensitivity: 800 mV/
	50 kohms
Digital (Coaxial)	Impedance: 75 ohms
Outputs (Analog)
AUDIO OUT	Voltage: 800 mV/
	10 kohms
SUBWOOFER	Voltage: 2 V/1 kohms
Tone
Gain levels	±6 dB, 1 dB step

Reproduction frequency range:

28 – 20,000 Hz

FM tuner section

Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced

Intermediate frequency

10.7 MHz

AM tuner section

Tuning range

With 10-kHz tuning scale:

530 – 1,710 kHz3)

With 9-kHz tuning scale:

531 – 1,710 kHz3)

AntennaLoop antenna

Intermediate frequency

450 kHz

3)You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING MODE, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

Video section

Inputs/Outputs

Video:	1 Vp-p, 75 ohms
COMPONENT VIDEO:		Additional
	Y: 1 Vp-p, 75 ohms	Additional
	Y: 1 Vp-p, 75 ohms
	PB/CB: 0.7 Vp-p,
	75 ohms
	PR/CR: 0.7 Vp-p,	Information
	75 ohms	Information
	75 ohms
	80 MHz HD Pass Through
General
Power requirements

Area code	Power requirements

U	120 V AC, 60 Hz

Power output (DIGITAL MEDIA PORT)
DC OUT	5 V, 700 mA

continued

81US

Contents

Page WARNING For customers in the United States –Reorient or relocate the receiving antenna –Increase the separation between the equipment and receiver –Consult the dealer or an experienced radio/TV technician for help •The instructions in this manual are for model HT-7100DH The HT-7100DHconsists of: • Receiver STR-K7100 • DVD player Table of Contents Description and location of parts KINPUT SELECTOR LMOVIE MA.F.D N2CH About the indicators on the display LFE ;PL OPT DTS SP B Name Function LCOAX is set to “AUTO IN” and the being input through the COAXIAL jack, or when Rear panel ADIGITAL INPUT/OUTPUT section OPTICAL IN jack player, etc. The EAUDIO INPUT/OUTPUT section FANTENNA section RM-AAP016 10US A AV ?/1 (on/standby) video components that the remote is programmed to operate If you press ?/1 (B) at the KOPTIONS Press to display and select items OPTIONS TOOLS TV, press TV (Z) and then press OPTIONS TOOLS DISC SKIP SCATEGORY Press to select the category for XM Radio REPLAY ADVANCE 1: Installing speakers You can install your surround speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws 15US 2: Connecting speakers 3a: Connecting the audio components 3b: Connecting the video components AAudio cord (not supplied) BVideo cord (not supplied) CComponent video cord (not supplied) Tips –connect the audio output jacks of the TV to the TV IN jack of the receiver –turn off or mute the TV’s volume The following illustration shows how to connect a DVD player/DVD recorder Connecting a DVD player •Do not bend or tie the optical digital cords All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies AA BB C AHDMI cable (not supplied) BCoaxial digital cord (supplied) COptical digital cord (not supplied) 22US If you connect a Blu-raydisc player Notes on HDMI connections Notes on digital audio signals connection 23US •Do not bend or tie optical digital cords BOptical digital cord (not supplied) CVideo cord (not supplied) 24US Connecting components with analog video and audio jack CAudio/video cord (not supplied) 25US 4: Connecting the antennas 5:Preparing the receiver and the remote 1 Press ?/1 to turn off the receiver 2 Hold down ?/1 for 5 seconds 3 Press MEMORY/ENTER 27US 6:Selecting the speaker system 7:Calibrating the appropriate settings automatically •Check the connection between each speaker and the receiver •Adjust the speaker level •Measure the distance of each speaker to your listening position Press AUTO CAL The measurement process will take a few minutes to complete The table below shows the display when measurement starts Measurement for Display Error codes To rectify the error Error codes and remedies Warning codes 31US To change the settings manually 1Record down the warning code 5Follow the solution provided in the “Warning codes and solutions” below Warning codes and solutions Warning 3-6 Gg Selecting a component To avoid damaging your speakers Before you turn off the receiver, be sure to turn down the volume level To listen to the sub woofer 1Press POWER The POWER indicator lights up Listening/Watching a component •Refer to the operating instructions supplied with the TV and DVD player •Check the following if you cannot listen to multi channel sound –Be sure the digital audio output of the DVD player is set up properly You can select the sound field to suit the movie/music. Refer to Music: CONCERT Navigating through menus 3-7 Gg Menu Parameters Settings Initial setting 40US Adjusting the level Adjusting the tone Settings for the surround sound Settings for the tuner Settings for the audio Settings for the video Settings for the system xSUR POS (Surround speaker position) •SIDE/LO •SIDE/HI •BEHD/LO Enjoying Dolby Digital and DTS Surround sound Press A.F.D. repeatedly to select the sound field you want For details, see “Types of A.F.D. mode” (page 48) Sound Surround Enjoying 47US Types of A.F.D. mode Decoding A.F.D. mode Multi channel Effect Selecting a preprogrammed sound field 49US Types of sound field available Sound field for Movie CINEMA STUDIO EX A Using only the front speakers and sub woofer Press 2CH 51US 2 While holding down 2CH, press ?/1 Listening to FM/AM radio 1 Press TUNER repeatedly to select the FM or AM band 2 Press TUNING + or TUNING – The receiver stops scanning whenever a station is received Using the controls on the receiver 1Turn INPUT SELECTOR to select the FM or AM band Presetting radio stations 5-8 Gg Listening to the XM Radio 1 Press TUNER repeatedly to select “XM RADIO” 2 Press TUNING + or TUNING – to select channel 57US 3 Check the XM Radio ID on the display and write it in the space provided here Display Description 1 Press TUNER repeatedly to select the “XM RADIO” 2 Press TUNING + or TUNING – to select a channel Selecting channels from a category (CATEGORY TUNING) 2 Press CATEGORY MODE repeatedly to select “ONE CAT” 3 Press CATEGORY + or CATEGORY – to select the category you want 4 Press TUNING + or TUNING – to select the channel Selecting channels by inputting the channel number directly Presetting XM Radio stations 2 Tune in the channel you want to preset For details on selecting channels, see “Listening to the XM Radio” (page 56) 4 Press the numeric buttons to enter the preset number 6 Repeat steps 2 to 5 to preset another channel 2 Press PRESET + or PRESET – repeatedly to select the preset channel you want XM Radio messages list Message appears The XM antenna is not Make sure that the antenna is securely connected Switching the audio input mode AVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Press and hold both sides of the connector and then pull out the connector 64US Notes 1 Press DMPORT You can also use the INPUT SELECTOR on the receiver to select “DMPORT” Initial setting: –NONE The assignable composite video input are VIDEO 1, VIDEO 3, DVD and SAT inputs 2 Start playback of the connected component Listening to digital sound from other inputs 3 Press V/v repeatedly to select “5-AUDIO” 5 Press V/v repeatedly to select “D.ASSIGN” 8 Press or b to enter your selection 66US Naming inputs Changing the display Using the Sleep Timer Recording using the receiver Press RM SET UP The RM SET UP indicator slowly flashes Programming the remote 2 Press the input button for the component you want to control 5 Repeat steps 1 to 4 to control other components •The indicator turns off while a valid button is pressed •For the numeric codes, only the last three numbers entered are valid If programming is unsuccessful, check the following: To clear the memory of the remote While holding down MASTER VOL –,press and hold ?/1 and then press AV ?/1 The indicator flashes 3 times, then goes off The numeric codes corresponding to the component and the maker of the component To control an LD player 601, 602 To control a video CD player MakerCode(s) SONY605 To control a TV 73US To control a satellite tuner To control a cable box To control a tuner To control a Blu-raydisc recorder To control a PSX Glossary Precautions Troubleshooting There is no sound from one of the front speakers There is no sound from analog 2 channel sources There is no sound from digital sources (from COAXIAL or OPTICAL input jack) Check that the INPUT MODE is not set to “ANALOG” •Check the HDMI connection Dolby Digital or DTS multi channel sound is not reproduced The MULTI CHANNNEL DECODING lamp does not light up in blue Recording cannot be carried out •Check that the components are connected correctly •Select the source component using the input buttons Radio stations cannot be tuned in Remote control The remote does not function •Point the remote at the remote sensor on the receiver •Remove any obstacles in the path between the remote and the receiver Specifications Power consumption Speaker section •Front speakers (SS-MSP7000) •Center speaker (SS-CNP900) •Surround speakers (SS-SRP7000) Index Sony Corporation