Main
WARNING
On safety
On power sources
On heat buildup
On placement
Precautions
Copyrights
About the S-AIR function
Table of contents
Getting Started
Playback Options
Surround Function
BRAVIA Sync Features
Unpacking
Install the subwoofer and speakers as shown in the illustration below.
To use the speakers efficiently
Installing the system
To connect the speaker cords to the speakers
To install the speakers on a flat surface
To install the speakers on the speaker stand
To install the speakers on a wall
1
2
3
Page
Connecting the speakers
White (speaker (L))
Red (speaker (R))
Speaker (R)Speaker (L)
Rear of the
Connecting components with HDMI jacks
Notes on HDMI connections
Connecting a component to the OPTICAL DIGITAL 1 IN jack
Connecting components without HDMI jacks
Connecting a component to the COAXIAL DIGITAL 2 IN jack
Page
Connecting the AM loop antenna (aerial)
1 2 3
4
Connecting the antenna (aerial)
P
ORT
Connecting the FM wire antenna (aerial)
Connect the FM wire antenna (aerial) to the FM 75 COAXIAL jack.
FM wire antenna (aerial) (supplied)
FM 75 COAXIAL jack
Outdoor FM antenna (aerial)
Connecting the other components
DIGITAL MEDIA PORT adapter : Signal flow
Rear of the
A
Using the wireless system
DMPORT
SPEAKER
There is no need to open the slot cover until the S-AIR product is used.
CAUTION
Index to parts and controls
Front panel display (subwoofer)
About the indications in the front panel display
Remote control
1
2 3 4
2 +/
Enjoying TV
TV (whit e)
1
2 +/
2
and the system on.
3 4
1
2
3
1 2
Surround Function
Enjoying the surround effect
Press NIGHT MODE.
To cancel the night mode, press NIGHT MODE again.
You can listen to Dolby Digital sound at low volume by using AUDIO DRC (page 44).
Enjoying the sound at low volume (NIGHT mode)
NIGHT MODE
The Control for HDMI function will not operate in the following cases:
1
2
BRAVIA Sync Features
What is BRAVIA Sync?
Preparing for the BRAVIA Sync
3
4
If SCANNING or COMPLETE does not appear after performing the steps above
2
3
4
6
7
If you add or reconnect the component
2
3
HDMI appears, then press or c.
4
Play back a connected component.
2
3
4
volume level you want.
The maximum volume level changes as follows:
Turning off the TV, system and connected components
(System Power Off)
AV ?/1
TV (yellow)
2
3
SAVE appears, then press or c.
4
Using the power saving function
2
auto scanning starts.
3 4
A preset number appears in the front panel display.
6
2
3
To turn off the radio
To listen to non-preset radio stations
If an FM program is noisy
2
3 4
6
If you enter a wrong character
7
Using the Radio Data System (RDS)
Controlling the component
1
DVD or SAT/CATV) to select the component you want to operate.
The component assigned to the selected input button becomes operable.
2
the corresponding button for the operation.
To control the Blu-ray Disc/DVD/ Hard disc recorder
To control the Blu-ray Disc/DVD player
To control the HDD/DVD COMBO
To control the satellite/cable television tuner
1
change the assignment of.
Example: Hold down DVD.
2
the corresponding button for the category you want.
1
2
3
The following pages show details for each setting.
Settings and adjustments using the amplifier menu
2
3
4
level.
Default setting: 0 (dB) You can adjust from 6 (dB) to +6 (dB) in 1 dB steps.
2
3
DRC appears, then press or c.
4
Adjusting the bass and treble level (BASS, TREBLE)
2
3
TREBLE appears, then press or c.
4
Default setting: 0 (dB) You can adjust from 6 (dB) to +6 (dB) in 1 dB steps.
2
3
appears, then press or c.
4
Default setting: 0 ms You can adjust from 0 ms to 200 ms in 10 ms steps.
2
3
MONO
4
Changing the brightness of the front panel display (DIMMER)
2
3
appears, then press or c.
4
the front panel display.
2
3
4
front panel display.
Using the sleep timer (SLEEP)
2
3
4
The minutes display (the remaining time) changes as follows:
This function is only for this system, not for the connected TV or other components.
1
Using an S-AIR product
2
3
DIGITAL
TV
DMPORT
1
The subwoofer turns on.
2 3
appears in the front panel display, then
When the wireless transmitter is not inserted in
2
appears in the front panel display, then
When the wireless transmitter is not inserted in
3
MODE appears in the front panel display, then press or c.
7
8
To control the system from the S-AIR receiver
Enjoying the S-AIR receiver while the subwoofer is in standby mode (S-AIR STANDBY MODE)
2
3
Identifying the subwoofer with a specific S-AIR sub unit (Pairing operation)
xAfter pairing
Sound transmission is established between the paired subwoofer and S-AIR sub unit(s) only.
1
to pair near the subwoofer.
2
S-AIR sub unit.
3 4
7
8
To cancel pairing
If sound transmission is unstable
2
7
Stabilizing S-AIR reception
About environments where S-AIR products (S-AIR main unit and sub unit) are used
When S-AIR reception is poor
General
Connected components
Additional Information
Troubleshooting
Control for HDMI
The S-AIR function
Other
Use buttons on the system for this operation.
1 2
and ?/1 at the same time.
Formats supported by this system
Digital input formats supported by this system are as follows.
Amplifier section
HDMI section
Tuner section
Speakers (SS-FS3)
Subwoofer (SA-WFS3)
General
Glossary
Page
Index
