Sony HT-FS3 7, 8, 2, 3

56GB

7Start pairing of the S-AIR sub unit.

Refer to the operating instructions of the

S-AIR sub unit.

When sound transmission is established,

“COMPLETE” appears for two seconds in

the front panel display.

• Perform pairing within several minutes of Step

6. If you do not, “FAILED” appears for two

seconds in the front panel display. To continue

pairing, press and start again from Step 3.

To cancel pairing, press AMP MENU.

8Press AMP MENU.

The AMP menu turns off.

• After you have performed pairing, if you select

“S-AIR ID” (page 54), the ID setting (“A,” “B,” or

“C”) that you last used is displayed first by default.

To cancel pairing

Perform the ID setting of the subwoofer

according to the procedure of “To set the ID of

the subwoofer.” If you select a new ID, pairing is

canceled.

If sound transmission is

unstable

If you use multiple wireless systems which share

the 2.4 GHz band, such as wireless LAN or

Bluetooth, the transmission of S-AIR products or

other wireless systems may be unstable. In this

case, the transmission may be improved by

changing the following “RF CHANGE” setting.

1Press AMP MENU.

2Press x/X repeatedly until “SET S-AIR”

appears in the front panel display, then

press or c.

3Press X/x repeatedly until “RF

CHANGE” appears in the front panel

display, then press or c.

Note

Note

SYSTEM STANDBY

MENU/HOME

TOOLS/

OPTIONS

TV VOL

MASTER VOL

123

46

78

0

ENTER

9

THEATRE TV

?/1

AV

?/1

TV BD DVD

DIGITAL1 DIGITAL2 TUNER/BAND DMPORT

SAT/CATV

TOP MENU

MENU

BD/DVD

RETURN/EXIT

TV

TUNING

-

TUNING

+

F1 F2

AMP MENU

CLEAR

DISPLAY

NIGHT

MODE

SOUND

FIELD

AUDIO

ANALOGDIGITAL

?/1

TV CH

-

PRESET

-

TV CH

+

PRESET +

F

Gg

f

.

mM

Xx

<

<

>

5

SYSTEM STANDBY

MENU/HOME

TOOLS/

OPTIONS

N

AMP

MENU

C, X, x, c,

Contents

Main WARNING On safety On power sources On heat buildup On placement Precautions Copyrights About the S-AIR function Table of contents Getting Started Playback Options Surround Function BRAVIA Sync Features Unpacking Install the subwoofer and speakers as shown in the illustration below. To use the speakers efficiently Installing the system To connect the speaker cords to the speakers To install the speakers on a flat surface To install the speakers on the speaker stand To install the speakers on a wall 1 2 3 Page Connecting the speakers White (speaker (L)) Red (speaker (R)) Speaker (R)Speaker (L) Rear of the Connecting components with HDMI jacks Notes on HDMI connections Connecting a component to the OPTICAL DIGITAL 1 IN jack Connecting components without HDMI jacks Connecting a component to the COAXIAL DIGITAL 2 IN jack Page Connecting the AM loop antenna (aerial) 1 2 3 4 Connecting the antenna (aerial) P ORT Connecting the FM wire antenna (aerial) Connect the FM wire antenna (aerial) to the FM 75 COAXIAL jack. FM wire antenna (aerial) (supplied) FM 75 COAXIAL jack Outdoor FM antenna (aerial) Connecting the other components DIGITAL MEDIA PORT adapter : Signal flow Rear of the A Using the wireless system DMPORT SPEAKER There is no need to open the slot cover until the S-AIR product is used. CAUTION Index to parts and controls Front panel display (subwoofer) About the indications in the front panel display Remote control 1 2 3 4 2 +/ Enjoying TV TV (whit e) 1 2 +/ 2 and the system on. 3 4 1 2 3 1 2 Surround Function Enjoying the surround effect Press NIGHT MODE. To cancel the night mode, press NIGHT MODE again. You can listen to Dolby Digital sound at low volume by using AUDIO DRC (page 44). Enjoying the sound at low volume (NIGHT mode) NIGHT MODE The Control for HDMI function will not operate in the following cases: 1 2 BRAVIA Sync Features What is BRAVIA Sync? Preparing for the BRAVIA Sync 3 4 If SCANNING or COMPLETE does not appear after performing the steps above 2 3 4 6 7 If you add or reconnect the component 2 3 HDMI appears, then press or c. 4 Play back a connected component. 2 3 4 volume level you want. The maximum volume level changes as follows: Turning off the TV, system and connected components (System Power Off) AV ?/1 TV (yellow) 2 3 SAVE appears, then press or c. 4 Using the power saving function 2 auto scanning starts. 3 4 A preset number appears in the front panel display. 6 2 3 To turn off the radio To listen to non-preset radio stations If an FM program is noisy 2 3 4 6 If you enter a wrong character 7 Using the Radio Data System (RDS) Controlling the component 1 DVD or SAT/CATV) to select the component you want to operate. The component assigned to the selected input button becomes operable. 2 the corresponding button for the operation. To control the Blu-ray Disc/DVD/ Hard disc recorder To control the Blu-ray Disc/DVD player To control the HDD/DVD COMBO To control the satellite/cable television tuner 1 change the assignment of. Example: Hold down DVD. 2 the corresponding button for the category you want. 1 2 3 The following pages show details for each setting. Settings and adjustments using the amplifier menu 2 3 4 level. Default setting: 0 (dB) You can adjust from 6 (dB) to +6 (dB) in 1 dB steps. 2 3 DRC appears, then press or c. 4 Adjusting the bass and treble level (BASS, TREBLE) 2 3 TREBLE appears, then press or c. 4 Default setting: 0 (dB) You can adjust from 6 (dB) to +6 (dB) in 1 dB steps. 2 3 appears, then press or c. 4 Default setting: 0 ms You can adjust from 0 ms to 200 ms in 10 ms steps. 2 3 MONO 4 Changing the brightness of the front panel display (DIMMER) 2 3 appears, then press or c. 4 the front panel display. 2 3 4 front panel display. Using the sleep timer (SLEEP) 2 3 4 The minutes display (the remaining time) changes as follows: This function is only for this system, not for the connected TV or other components. 1 Using an S-AIR product 2 3 DIGITAL TV DMPORT 1 The subwoofer turns on. 2 3 appears in the front panel display, then When the wireless transmitter is not inserted in 2 appears in the front panel display, then When the wireless transmitter is not inserted in 3 MODE appears in the front panel display, then press or c. 7 8 To control the system from the S-AIR receiver Enjoying the S-AIR receiver while the subwoofer is in standby mode (S-AIR STANDBY MODE) 2 3 Identifying the subwoofer with a specific S-AIR sub unit (Pairing operation) xAfter pairing Sound transmission is established between the paired subwoofer and S-AIR sub unit(s) only. 1 to pair near the subwoofer. 2 S-AIR sub unit. 3 4 7 8 To cancel pairing If sound transmission is unstable 2 7 Stabilizing S-AIR reception About environments where S-AIR products (S-AIR main unit and sub unit) are used When S-AIR reception is poor General Connected components Additional Information Troubleshooting Control for HDMI The S-AIR function Other Use buttons on the system for this operation. 1 2 and ?/1 at the same time. Formats supported by this system Digital input formats supported by this system are as follows. Amplifier section HDMI section Tuner section Speakers (SS-FS3) Subwoofer (SA-WFS3) General Glossary Page Index