ICF-C1iPMK2_U2 [US] 3-873-060-15(1)

 
CR2032

CR2025
There is a tactile dot on the VOL +, /, and PRESET + button.FM wire antennaAC power cordThere is a tactile dot on the VOLUME +, / and PRESET TUNING 3 button.

About the backup

battery

To keep good time, as a backup power source, this unit
has one CR2032 battery inside of the unit in addition
to the house current.
The battery keeps the clock and the alarm operating in
the event of a power interruption.
Note that the backlight will not light up during a
power interruption.
Knowing when to replace the battery
If a power interruption occurs when the battery is
weak, the brightness of characters in the display
darkens. If the battery runs out during the
interruption, the current time and alarm functions will
be initialized.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may present a risk of
fire or explosion.
Replacing the backup battery
1 Keep the AC plug connected to the AC
outlet, remove the screw that secures the battery compartment at the bottom of the unit using a screwdriver, and remove the battery compartment. (See Fig. -)
2 Insert a new battery in the battery
compartment with the side facing up.
To remove the battery from the battery
compartment, push it out from the side marked
PUSH. (See Fig. -)
3 Insert the battery compartment back into
the unit and secure it with the screw. (See Fig. -)
Note
When you replace the battery, keep the AC plug
connected to a wall outlet. Otherwise, current time
and alarms will be initialized if the replacement is not
completed within around one minute.
If the time in the display is incorrect after the battery is changed (RESET)
Push the Reset switch with the pointed device. The
Reset switch is in the small hole located in the battery
compartment.
Notes
You cannot reset unless the lithium battery is
installed.
Set the clock again after the unit is reset.
Battery Warning
When the unit will be left unplugged for a long time,
remove the battery to avoid undue battery discharge
and damage to the unit from battery leakage.

Preparing the remote

commander

Before using the card remote commander for the first
time, remove the insulation film. (See Fig. -)
When to replace the battery
With normal use, the battery (CR2025) should last for
about six months. When the remote commander no
longer operates the unit, replace the battery with new
ones. (See Fig. -)
Notes
Do not charge the battery.
When you are not going to use the remote
commander for a long time, remove the battery to
avoid any damage caused by leakage and corrosion.

Setting the clock for the

first time

This unit is preset to the current date and time at the
factory, and is powered by the back up battery. All you
need to do the first time is just plug it in and select
your time zone.
1 Plug in the unit.
2 Press TIME ZONE for more then two
seconds.
Area number “2” appears in the display.
If you live in the Eastern Time zone, you do not
need to adjust the area setting.
Area number Time zone
1 Atlantic Standard/Daylight Time
2
(default)
Eastern Standard/Daylight Time
3 Central Standard/Daylight Time
4 Mountain Standard/Daylight Time
5 Pacific Standard/Daylight Time
6 Yukon Standard/Daylight Time
7 Hawaiian Standard/Daylight Time
3 Press TIME SET + or – repeatedly until the
desired number appears.
4 Press TIME ZONE to complete the setting.
Note
During the shipment and your first use, a clock error
may occur. In this case, refer to “Setting the clock and
date” to set the correct time.
When daylight saving time (summer time) begins
This model employs the Automatic Daylight Saving
Time/Summer Time adjustment. The DST indicator in
the display appears in the display at the beginning of
the daylight saving time (summer time), and
disappears at the end of it.
Daylight saving time begins at: 2:00 AM on the
second Sunday of March.
Standard time begins at: 2:00 AM on the first
Sunday of November.
To deactivate the Automatic DST/Summer Time adjustment during the daylight saving time (summer time) period.
The Automatic DST/Summer Time adjustment can be
cancelled.
Press CLOCK and TIME ZONE/ALARM DISPLAY for
more than two seconds. The Automatic DST/Summer
Time adjustment will be cancelled. To active the
Automatic DST/Summer Time adjustment again,
repeat the same operation.

Setting the clock and

date

To change the setting manually, follow the procedure
from step 1.
1 Press CLOCK for more than 2 seconds.
The year will start to flash in the display.
2 Press TIME SET + or – until the correct year
appears in the display.
3 Press CLOCK.
4 Repeat steps 2 and 3 to set the month, day
and time.
After setting the minute the clock starts from
0 seconds. But if you do not set “Minute”, the clock
does not start from 0 second flat.
Pressing and holding + or – changes the year,
month, day or time rapidly.
While setting the clock, you must perform each step
within about 65 seconds, or the clock setting mode
will be cancelled.
To display the year and datePress CLOCK once for the date, and within about 5 seconds press it again for the year.
The display shows the date or year for about
5 seconds and then changes back to the current time.

Setting the brightness

of the display

Three levels of brightness are available by pressing SNOOZE/BRIGHTNESS.

Playing the iPod

You can enjoy iPod audio by connecting this unit. To
use an iPod, refer to the user’s guide of your iPod.
Compatible iPod models
The compatible iPod models are as follows. Update
your iPod to use the latest software before you use it.
iPod nano
3rd generation
(video)
iPod touch
2nd generation
iPod nano
2nd generation
(aluminium)
iPod classic
iPod
5th generation
(video)
iPod nano
4th generation
(video)
iPhone
iPod touch
1st generation
iPod nano
5th generation
(video camera)
iPod nano
1st generation
iPod mini
iPod
4th generation
iPod
4th generation
(color display)
Notes
The connector of the unit is for sole use for iPod.
When you use the devices do not match with the
connector, connect it to the AUDIO IN terminal of
this unit with the supplied audio connecting cable.
Sony cannot accept responsibility in the event that
data recorded to iPod is lost or damaged when using
an iPod connected to this unit.
1 Put the iPod into the unit’s connector.
Adjust the rear support forward or backward
checking the back of the iPod fits snugly against
the rear support to protect the connector.
2 Press /.
The iPod begins to play automatically.
You can operate the connected iPod by the unit or
iPod buttons.
To Press
Turn off the iPod OFF, or press and hold
Pause playback /
To resume play, press it again.
Go to the next
track
Go back to the
previous track
Locate a point
while listening to
the sound
(forward) or
(backward) while playing and
hold it until you find the point.
Locate a point
while observing
the display
(forward) or
(backward) in pause and hold it
until you find the point.
Go back to the
previous menu
MENU*
Select a menu
item or a track for
playback
/*
Execute the
selected menu or
the playback
ENTER*
* These operations are available only when using the
supplied remote commander.
Notes
When placing or removing the iPod, keep it straight
and parallel with the rear support.
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
When placing or removing the iPod, brace the unit
with one hand and take care not to press the controls
of the iPod by mistake.
Do not pull on the rear support strongly as it cannot
be detached from the unit and may cause a
malfunction.
To use an iPod, refer to the user’s guide of your iPod.
Before disconnecting the iPod, pause playback.
Tip
Apple’s iPod Universal Dock Adapter can be used with
this unit.
To use the unit as a battery charger
You can use the unit as a battery charger.
The charging begins when the iPod is placed on the
connector.
The charging status appears in the iPod display. For
details, see the user’s guide of your iPod.
On copyrights
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
iPhone is a trademark of Apple Inc.
All other trademarks and registered trademarks are
of their respective holders. In this manual, ™ and ®
marks are not specified.

Playing the radio

—Manual tuning
1 Press RADIO ON to turn on the radio.
The display shows the band and frequency.
2 Press RADIO ON repeatedly to select the
desired band.
Each press changes the band as follows:
FM1 and FM2 are the same frequency bands.
3 Use TUNING + or – to tune into the desired
station.
The FM frequency advances or reverses in 0.1
MHz channel steps and the AM frequency in 10
kHz channel steps.
4 Adjust volume using VOLUME.
To turn off the radio, press OFF.

Improving the

reception

FM: Extend the FM wire antenna fully to
increase reception sensitivity.
AM: Connect the supplied AM loop antenna
to the unit. Rotate the antenna
horizontally for optimum reception.
Keep away digital music player or mobile phone from
the AM loop antenna or the FM wire antenna, as this
may lead to interference of reception.
Note
When you are listening to the radio with an iPhone
connected to the unit, interference with radio
reception may occur.
Tip
If the FM broadcast is noisy, press FM MODE on the
remote commander to turn off “STEREO” in the
display. The radio becomes clearer although the sound
becomes monaural.

Presetting your

favourite station

—Preset tuning
You can preset up to 10 stations in FM (5 stations in
FM1, 5 stations in FM2), and 5 stations in AM.
Presetting a station
1 Follow steps 1 to 4 in “Playing the Radio”
and manually tune into the station you wish to preset.
2 Press and hold the desired PRESET
TUNING button for more than two seconds for registration.
After the preset has finished, the preset number
appears on the display.
Example: To preset AM 1 260 kHz onto preset
2 button.
a few seconds after
To preset another station, repeat these steps.
To change the preset station, tune into the desired
station and hold down the PRESET TUNING 1 to
5 button. The new station will replace the previous
station on the preset button.
Tuning into a preset station
1 Press RADIO ON to turn on the radio.
2 Press one of the PRESET TUNING buttons
where the desired station is stored.
3 Adjust volume using VOLUME.

Setting the alarm

The dual alarm function allows you to set two alarm
programs (ALARM A and ALARM B).
The alarm time can be set for each program and the
alarm sound is selectable from RADIO, BUZZER or
iPod.
Notes
Before setting the alarm, make sure to set the clock
(see “Setting the clock and date”).
The factory setting alarm time is “AM 12:00”.
To set the radio alarm, first tune in to a station
(see “Playing the radio”).
To set the alarm time
To set ALARM A
1 Press ALARM SET A for a few seconds.
2 Press TIME SET +/– to set the desired hour,
and press ALARM SET A.
3 Press TIME SET +/– to set the desired
minute, and press ALARM SET A.
4 Press TIME SET +/– to set the desired alarm
mode (RADIO, BUZZER or iPod) and press ALARM SET A.
5 If you select the RADIO or iPod, press TIME
SET +/– to set the wake up volume and press ALARM SET A.
To set ALARM B, follow the same steps above using
ALARM B instead of ALARM A.
To change the display between ALARM TIME A and
ALARM TIME B, press TIME ZONE/ALARM DISPLAY.
When using iPod touch/iPhone
To use music stored in an iPod touch/iPhone to wake
up, put the iPod touch/iPhone into the unit first,
follow the steps above to set alarm time, and then
select the desired music.
Notes
When you use the radio alarm, the timed alarm
sounds with the last broadcasting station tuned to
before the power went off. When you set the radio
alarm, select the desired broadcasting station before
turning the power off.
The ALARM A (or B) indicator flashes in the display
when the alarm sounds.
If a second alarm sounds during a first (or the
SNOOZE function is active), the second alarm takes
priority.
The alarm function works as usual at the beginning
and end day of the daylight saving time (summer
time). While the Automatic DST/Summer Time
adjustment is set, as a result, if the alarm is set at a
time skipped when the daylight saving time
(summer time) begins, the alarm is skipped, or if the
alarm is set at a time overlapped when the daylight
saving time (summer time) ends, the alarm sounds
twice.
If the same alarm time is set for both alarm
(ALARM A and B), the ALARM A takes priority.
To activate the alarmAfter setting the alarm time, follow these steps:To activate the ALARM A, press ALARM SET A to display ALARM A.To activate the ALARM B, press ALARM SET B to display ALARM B.
Notes
The alarm sounds at the set time even if the unit is
on.
Make sure the iPod is installed correctly after setting
the iPod alarm.
Notes on using iPod touch/iPhone
If you set the iPod alarm while iPod touch/iPhone
music is playing, and then turn the unit power off,
when the alarm time comes on, the alarm music will
resume from the point where the power was turned
off.
Even if the iPod alarm setting is complete, if you
turn the iPod touch/iPhone power off before the
unit, the iPod alarm will not work.
To doze for a few more minutesPress SNOOZE/BRIGHTNESS.
The sound turns off but will automatically come on
again after about 5 minutes.
The maximum length of the snooze time is
40 minutes.
To stop the alarmPress OFF to turn off the alarm.
The alarm will come on sound again at the same time
the next day.
If OFF is not pressed, the buzzer alarm sounds
continuously for about 3 minutes, and then it stops
automatically.
The RADIO and iPod sound continuously until OFF is
pressed.
To deactivate the alarmPress ALARM SET A (or B) to turn off the ALARM A (or B) indicator from the display.
Note on alarm in the event of a power
interruption
When the alarm sound is set to RADIO or iPod, it
will change to BUZZER automatically.
If the backup battery is exhausted, the alarm will not
work in the event of power interruption. Replace the
battery periodically.

Setting the sleep timer

You can fall asleep to the sound using the built-in
sleep timer that turns off the unit automatically after a
preset duration.
1 Press SLEEP while the unit is turned on.
SLEEP appears in the display.
2 Press SLEEP to set the sleep timer duration.
Each time you press SLEEP, the duration changes
as follows:
The display returns to clock mode five seconds
after you have finished setting the duration setting
and released SLEEP, and then the sleep timer
starts.
The unit will play for the duration you set, and
then shut off.
To turn off the unit before the preset timePress OFF.To use both sleep timer and alarm
You can fall asleep to the radio and also be awakened
by the radio or buzzer alarm at the preset time.
1 Set the alarm. (See “Setting the alarm”.)
2 Set the sleep timer. (See “Setting the sleep
timer”.)

Other useful functions

To get the MEGA Xpand effect
Press MEGA Xpand. “MEGA Xpand” appears in the
display. You can get the effect of expansion of the
sound field. To return to normal sound, press the
button again.

Connecting external

equipment

To listen to sound
1 Connect the AUDIO IN jack of the unit to
the line out jack or headphone jack of the external equipment using the audio connecting cable (supplied).
2 Press AUDIO IN to display “AUDIO IN”.
3 Play the equipment connected to the
AUDIO IN jack.
4 Adjust the volume using VOLUME.
To return to the radioPress RADIO ON.
The frequency is shown in the display.
To return to the iPodPress /.To stop listeningPress OFF, and stop playback on the connected unit.