2
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not disassemble. Refer servicing to qualified personnel only.
Caution
The use of optical instruments with this product will increase eye hazard. As the laser beam used in this unit is harmful to eyes, do not attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
This label is located on the Laser protective housing inside the enclosure.
This graphical symbol with supplemental marking is located on the right surface of the unit (when it is in a vertical position).
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the console.
Caution
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Information
For Customers in the USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
If you have any questions about this product, you may call:
Sony Computer Entertainment America PlayStation Consumer/Technical Support
Declaration of Conformity
Trade Name : | SONY |
Model No. : | |
Responsible Party : | Sony Electronics Inc. |
Address : | 680 Kinderkamack Road, |
| Oradell, NJ 07649 U.S.A. |
Telephone No. : |
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Before operating your PlayStation®2 console
A few people may experience epileptic seizures when viewing flashing lights or patterns in our daily environ- ment. These persons may experience seizures while watching TV or playing video games, including DVD videos or games played on the PlayStation®2 console. Players who have not had any seizures may nonetheless have an undetected epileptic condition.
Consult your physician before operating the PlayStation®2 console if you have an epileptic condition or experience any of the following symptoms while watching TV programs or playing video games: altered vision, muscle twitching, other involuntary movements, loss of awareness of your surroundings, mental confusion, and/ or convulsions.
Owner’s Record
The model and serial numbers are located on the rear of the PlayStation®2 console. Record the appropriate number in the space provided below. Refer to these numbers whenever you call for technical assistance at
Model No.
Serial No. _______________________________
Precautions
Disc handling
•Do not leave discs near a heat source, in direct sunlight, or in high humidity.
•Store discs in their cases when they are not being used. Stacking discs or standing them at an angle without putting them in their cases can cause the discs to warp.
•Do not touch the disc surface when handling a disc; hold it by the edges.
•Do not stick paper or tape onto the disc.
•Do not write on the disc with a marker, etc.
•Fingerprints or dust on the disc can distort the picture or reduce sound quality. Make sure discs are always clean before use.
•Clean discs using a soft cloth, lightly wiping from the center outwards.
•Do not use solvents such as benzine, commercially available cleaners not intended for CDs or
Do not place the console in an unusually hot location
Do not leave the console in a car with its windows closed (particularly in summer) as this may warp the exterior of the console or cause the console to malfunction.
Moisture condensation
If the console or the disc is brought directly from a cold location to a warm one, moisture may condense on the lens inside the console or on the disc. Should this occur, the console may not operate properly. In this case, remove the disc and do not put the disc back in until the moisture evaporates. (This could take several hours.) If the console still does not operate properly, call
Do not subject the console to violent physical shock
Do not throw or drop the console or its accessories, and do not knock the console or its accessories against other objects. When carrying the console, do not subject it to any type of violent physical shock. This may damage the disc or cause the console to malfunction.
Avoid damaging the exterior of the console
Do not apply any solvents, and do not place any rubber or vinyl materials on the surface of the console for an extended period of time. Doing so may damage the plastic surface or cause the paint to peel off.
Cleaning the exterior of the console
When cleaning the exterior of the console, be sure to turn the power off with the MAIN POWER switch on the back of the console and disconnect the AC power plug from the electrical socket.
•If the exterior of the console becomes dirty, soak a soft cloth in a mild detergent solution diluted with water, tightly squeeze the cloth to remove the excess liquid, wipe the affected area of the exterior and finish by wiping with a dry cloth.
•Do not use benzine or paint thinner to clean the exterior of the console since these may damage the surface or cause the paint to peel off. When using a chemically- treated dust cloth, follow the usage instructions supplied with it.
Never disassemble the console
•Use your PlayStation®2 computer entertainment system according to the instructions in this manual. No authorization for the analysis or modification of the PlayStation®2 console, nor the analysis and use of its circuit configurations, is provided herein.
•There are no
Notes on safety when using the analog controller (DUALSHOCK™2) and analog controller (DUALSHOCK™)
•Stop using this console immediately if you begin to feel tired or if you experience discomfort or pain in your hands and/or arms while operating the controller. If the condition persists, consult a doctor.
•Do not attempt to operate the controller in any way except with your hands. Do not bring the controller into close contact with your head, face or near the bones of any other part of your body.
•The vibration function of the analog controller (DUALSHOCK™2) or the analog controller (DUALSHOCK™) can aggravate injuries.
Do not use the vibration function of the analog controller (DUALSHOCK™2) and analog controller (DUALSHOCK™) supported by software if you have any ailment in the bones or joints of your hands or arms.
•Do not use the analog controller (DUALSHOCK™2) or the analog controller (DUALSHOCK™) with software that supports the vibration function if you have injuries or ailments to the bones or muscles of your fingers, hands, wrists or arms. The vibration of the controller may aggravate such conditions.
•Avoid prolonged use of the analog controller (DUALSHOCK™2) and analog controller (DUALSHOCK™). Take a break at about 30 minute intervals.