DR (Disaster Recovery*) Mode

To enable DR Mode, set position 1 [Drive Mode] switch to ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

DR (Disaster Recovery) Mode (ON)

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Emulation Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

AIT Library Interface Mode

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Terminator Power

1

 

2

3

4

5

6

7

8

 

6

Periodic Cleaning Req

 

 

7

DC Control (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

DC Control (2)

*In Disaster Recovery Mode, an SDX-900V series drive enters the DR Standby Mode 15 seconds after you insert a write-protected tape into the drive, and all the drive LED blink. If you restart the drive while the LED are blinking, it starts as a CD-ROM device.

For details about the Disaster Recovery Mode, refer to the instruction manual that came with the application software you are using.

Emulation Mode*

To enable Emulation Mode, set the position 2 [Drive Mode] switch to ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

DR (Disaster Recovery) Mode

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Emulation Mode (ON)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

AIT Library Interface Mode

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Terminator Power

1

2

3

4

5

6

7

8

 

6

Periodic Cleaning Req

 

7

DC Control (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

DC Control (2)

*Emulation Mode returns the following in the Product Identification field of Inquiry of a SDX-900V series drive.

SDX-700C

Data Compression Control DIP switch

Data compression can be selected by DIP switches. Data compression is enabled while position 7 [DC Control (1)] is ON. Control by host can be disabled when position 8 [DC Control (2)] is ON.

12