Pin No. | Pin Name | I/O | Description | |
51 | O | Control rear relay on/off | ||
|
|
|
|
|
52 | O | Control center relay | ||
|
|
|
|
|
53 | O | Control speaker relay | ||
|
|
|
|
|
54 | O | Control Headphone relay | ||
|
|
|
|
|
55 | WOOFER RY | O | Control Woofer relay | |
|
|
|
|
|
56 |
|
| I | Detect power switch key |
SYS.POWER | ||||
|
|
|
|
|
57 | P115 | — |
| |
|
|
|
|
|
58 | P114 | — |
| |
|
|
|
|
|
59 | FUNC.MUTE | O | Control muting circuit | |
|
|
|
|
|
60 | P112 | — |
| |
|
|
|
|
|
61 | SP SW | I | Read speaker switch comdition | |
|
|
|
|
|
62 | P110 | — |
| |
|
|
|
|
|
63 | SET UP LED | O | Control Setup LED | |
|
|
|
|
|
64 | NAME LED | O | Control Name LED | |
|
|
|
|
|
65 | LEVEL LED | O | Control LEVEL LED | |
|
|
|
|
|
66 | SURR LED | O | Control SURR LED | |
|
|
|
|
|
67 | P103 | — |
| |
|
|
|
|
|
68 | S.FIELD LED | O | Control SF LED | |
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this necessary note is printed in each block.)
For schematic diagrams.
Note:
•All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
•All resistors are in Ω and 1/4 W or less unless otherwise specified.
•% : indicates tolerance.
•f : internal component.
•2 : nonflammable resistor.
•1 : fusible resistor.
•C : panel designation.
Note: | Note: |
The components identified by | Les composants identifiés par |
mark !or dotted line with mark | une marque ! sont critiques |
!are critical for safety. | pour la sécurité. |
Replace only with part number | Ne les remplacer que par une |
specified. | pièce portant le numéro spécifié. |
|
|
For printed wiring boards.
Note:
•X : parts extracted from the component side.
•a : Through hole.
•f : internal component.
•b: Pattern from the side which enables seeing.
C |
|
Q | These are omitted. |
B E |
|
B C E
These are omitted.
69 | B.B. LED | O | Control Bass Boost LED | |
70 | P100 | — |
| |
|
|
|
|
|
71 – 74 | P97 | – P94 | — |
|
|
|
|
|
|
75 – 78 | S15 | – S12 | O | Output signal to FL tube |
|
|
|
| |
79 | VLOAD | I | Negative power supply | |
|
|
|
| |
80 – 84 | S11 – S7 | — |
| |
|
|
|
|
|
85 – 90 | S6 | – S1 | O | Output signal to FL tube |
|
|
|
| |
91 – 100 | DIG10 – DIG1 | O | Output signal to FL tube | |
3-4. CIRCUIT BOARDS LOCATION
STANDBY board
SECONDARY board
VOL-SEL board
•U : B+ Line.
•V : B– Line.
•H : adjustment for repair.
•Voltages and waveforms are dc with respect to ground under
No mark : FM
•Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.
•Waveforms are taken with a oscilloscope.
•Circled numbers refer to waveforms.
•Signal path. F : FM J : CD g : VIDEO I : PHONO
•Abbreviation
CND : Canadian model.
AUS | : Australian model. |
SP | : Singapore model. |
MY | : Malaysia model. |
• Waveform
– MAIN SECTION –
1IC1 qf
– PANEL SECTION –
2IC103 qa
PRIMARY board
POWER SWITCH board
HEADPHONE board
DISPLAY board
ENCODER board
VIDEO board
MAIN board
TUNING board
AR | : Argentine model. |
CH | : Chinese model. |
MX | : Mexican model. |
CIS | : Russian model. |
EA | : Saudi Arabia model. |
EE | : East European model. |
99
