Manuals / Brands / Home Audio / Stereo Receiver / Sony / Home Audio / Stereo Receiver

Sony STR-DE475, STR-K402, STR-K402 Direct Tuning, Automatic Tuning, Area code, Press TUNER, 1Press TUNER, 1Press TUNER, FM tuning scale, AM tuning scale, Broadcasts Receiving

1 52

Download 52 pages, 622.3 Kb

Direct Tuning

Automatic Tuning

Broadcasts Receiving

For details on the buttons used in this section, see “Brief descriptions of buttons used to receive broadcasts” on page 35.

1Press TUNER.

The last received station is tuned in.

2Press FM or AM to select the FM or AM band.3Press D.TUNING on the remote.4Press the numeric buttons on the remote to enter the frequency.Example 1: FM 102.50 MHz

1 b 0 b 2 b 5 b 0

Example 2: AM 1350 kHz

(You don’t have to enter the last “0” when the tuning interval is set to 10 kHz)

1 b 3 b 5 b 0

If you cannot tune in a station and the entered numbers flash

Make sure you’ve entered the right frequency. If not, repeat Steps 3 and 4.

If the entered numbers still flash, the frequency is not used in your area.

5If you’ve tuned in an AM station, adjust the direction of the AM loop antenna for optimum reception.

6Repeat Steps 2 to 5 to receive other stations.zIf you try to enter a frequency not covered by the tuning interval

The entered value is automatically rounded up or down.

This tuning scale for direct tuning differs depending on the area code as shown in the following table. For details on area codes, see page 3.

Area code	FM tuning scale	AM tuning scale
U, CA	50 kHz	10 kHz (can be changed
		to 9 kHz)*

E2, E3, TW	50 kHz	9 kHz (can be changed
		to 10 kHz)*

AU	50 kHz	9 kHz

* To change the AM tuning scale, see page 45.

For details on the buttons used in this section, see “Brief descriptions of buttons used to receive broadcasts” on page 35.

1Press TUNER.

The last received station is tuned in.

2Press FM or AM to select the FM or AM band.

3Press TUNING + or TUNING –.

Press the + button to scan from low to high; press the – button to scan from high to low.

When the receiver reaches either end of the band

Scanning is repeated in the same direction.

The receiver stops scanning whenever a station is received.

4To continue scanning, press TUNING + or TUNING – again.

36

Contents

Owner’s Record WARNING Precautions About This Manual Unpacking Inserting batteries into the remote Before you get started Antenna Hookups Terminals for connecting the antennas Notes on antenna hookups Audio Component Hookups Required cords Jacks for connecting audio components Video Component Hookups Jacks for connecting video components Note on video component hookups Digital Component Hookups Example of LD player connected via an RF demodulator MULTI CH IN Hookups Example of a DVD player hookup using the MULTI CH IN jacks Other Hookups Setting the VOLTAGE SELECTOR (models of area code E2, E3 only) Connecting the AC power cord Hooking Up and Setting Up the Speaker System Brief descriptions of buttons and control Speaker System Hookup Terminals for connecting the speakers Notes on speaker system hookup To avoid short-circuitingthe speakers To avoid damaging your speakers Performing Initial Setup Operations Clearing the receiver’s memory Performing initial setup operations Multi Channel Surround Setup Specifying the speaker parameters Multi Channel Surround Setup xSurround speaker height (SLSR) xSub woofer selection xFront speaker distance (L R ) xCenter speaker distance ( C ) xSurround speaker distance (SLSR) Adjusting the speaker volume Before You Use Your Receiver Checking the connections Before You Use Your Receiver Location of Parts and Basic Operations Front Panel Parts Descriptions Front Panel Parts Description qa INPUT MODE button Select qs Function buttons To select qd MASTER VOLUME control Enjoying Surround Sound Brief descriptions of buttons used to enjoy surround sound Selecting a Sound Field Selecting a Sound Field Sound field information Sound field information Use the buttons on the front panel to operate the following modes Understanding the Multi-ChannelSurround Displays Source sound displays Source sound and Output Channel Display Input Channel Display All speakers absent Customizing Sound Fields To get the most from multi channel surround sound Adjusting the surround parameters Adjusting the level parameters Customizing Sound Fields Adjusting the bass/treble Resetting customized sound fields to the factory settings Adjustable parameters for each sound field Receiving Broadcasts receive broadcasts Direct Tuning Automatic Tuning Preset Tuning Presetting radio stations Tuning to preset stations Brief descriptions of buttons that appear in this chapter Naming Preset Stations and Program Sources Recording Recording on an audio tape or MiniDisc Recording Recording on a video tape Using the Sleep Timer Adjustment Using the SET UP Button Selecting the MULTI CH IN video input Set the display to turn off Additional Information Troubleshooting Reference sections for clearing the receiver’s memory Specifications AUDIO POWER SPECIFICATIONS Amplifier section FM tuner section AM tuner section Video section General Glossary Settings Using SURR, LEVEL, and SET UP buttons Remote Button Description Changing the factory setting of a function button Remote Button Description Index