Sony STR-DE545 Direct Tuning, Automatic Tuning

39

Receiving Broadcasts

bb

35

1

Direct Tuning

For details on the buttons used in this section, see “Brief

descriptions of buttons used to receive broadcasts” on

page 38.

1Press TUNER.

The last received station is tuned in.

2Press FM/AM to select the FM or AM band.

3Press D.TUNING on the remote.

4Press the numeric buttons on the remote to enter

the frequency.

Example 1: FM 102.50 MHz

Example 2: AM 1350 kHz

(You don’t have to enter the last “0” when the tuning interval

is set to 10 kHz)

If you cannot tune in a station and the

entered numbers flash

Make sure you’ve entered the right frequency. If not,

repeat Steps 3 and 4.

If the entered numbers still flash, the frequency is not

used in your area.

5If you’ve tuned in an AM station, adjust the

direction of the AM loop antenna for optimum

reception.

6Repeat Steps 2 to 5 to receive other stations.

zIf you try to enter a frequency not covered by the tuning

interval

The entered value is automatically rounded up or down.

Tuning intervals for direct tuning are:

FM: 50 kHz

AM: 10 kHz (to change to 9 kHz, see page 48.)

Automatic Tuning

For details on the buttons used in this section, see “Brief

descriptions of buttons used to receive broadcasts” on

page 38.

1Press TUNER.

The last received station is tuned in.

2Press FM/AM to select the FM or AM band.

3Press TUNING + or TUNING –.

Press the + button to scan from low to high; press the –

button to scan from high to low.

When the receiver reaches either end of the

band

Scanning is repeated in the same direction.

The receiver stops scanning whenever a station is

received.

4To continue scanning, press TUNING + or TUNING –

again.

bbbb

0250

1

Contents

Main WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. INFORMATION CAUTION Note to CATV system installer: TABLE OF CONTENTS Hooking Up the Components 4 Hooking Up and Setting Up the Speaker System 12 Location of Parts and Basic Operations 22 Enjoying Surround Sound 27 Hooking Up the Components Unpacking Inserting batteries into the remote z Before you get started Antenna Hookups ANTENNA FM 75 COAXIAL Notes on antenna hookups Ground wire (not supplied) To ground Audio Component Hookups IN OUT CD player Jacks for connecting audio components Digital Component Hookups Example of LD player connected via an RF demodulator RF demodulator LD player DIGITAL DVD/LD IN (COAXIAL) or (OPTICAL) * 5.1CH Input Hookups Two for the 5.1CH INPUT FRONT and REAR jacks Monaural audio cords (not supplied) Two for the 5.1CH INPUT CENTER and WOOFER jacks Video cord (not supplied) b AC power cord To a wall outlet AC OUTLET Control A1 connecting cord (not supplied) (STR-DE545 and STR-SE501 only) CONTROL A1 hookup (STR-DE545 and STR-SE501 only) AUX AUDIO IN hookup Connecting the AC power cord MULTI CHANNEL DECODING ? / 1 Hooking Up and Setting Up the Speaker System Jog dial Brief descriptions of buttons and control used to set up the speaker system Cursor buttons Speaker System Hookup Hooking Up and Setting Up the Speaker System INPUT Center speaker AUDIO IN Speaker impedance (STR-DE545 and STR-SE501 only) Speaker System Hookup To avoid short-circuiting the speakers To avoid damaging your speakers Performing Initial Setup Operations Before turning on the receiver Clearing the receivers memory 1 2 Performing initial setup operations Multi Channel Surround Setup z Multi Channel Surround Setup z Adjusting the speaker volume 2 3 4 z Before turning on the receiver Before You Use Your Receiver z Page Front Panel Parts Descriptions Location of Parts and Basic Operations Page 8!@! Front Panel Parts Description !! ! !9 ! !! @@@@! Page Front Panel Parts Description Enjoying Surround Sound Selecting a Sound Field 1 2 z Brief descriptions of buttons used to enjoy surround sound Sound field information Sound field Effect Notes Selecting a Sound Field Sound field information Sound field Effect Notes Notes Use the buttons on the front panel to operate the following modes Understanding the Multi-Channel Surround Displays Recording Notes 1/0 2/0* 3/0 2/1 3/1 2/2 3/2 2/0** DOLBY DIGITAL [1/0] DTS [1/0] DOLBY PROLOGIC PCM XX kHz*** Customizing Sound Fields To get the most from multi channel surround sound Adjusting the surround parameters 2 Adjusting the level parameters 2 Adjusting the bass/treble 5 z Resetting customized sound fields to the factory settings 1 2 z Adjustable parameters for each sound field Customizing Sound Fields Receiving Broadcasts This chapter describes how to receive FM or AM broadcasts and how to preset selected stations. Receiving Broadcasts Brief descriptions of buttons used to receive broadcasts STR-DE445 only Numeric buttons D.TUNING DVD/LD Direct Tuning 2 3 4 5 6 z Preset Tuning Presetting radio stations 2 3 4 Other Operations Brief descriptions of buttons that appear in this chapter Cursor buttons Naming Preset Stations and Program Sources 1 2 3 4 5 Using the Sleep Timer z Adjustment Using the SET UP Button Troubleshooting Additional Information Reference sections for clearing the receivers memory Troubleshooting Specifications AUDIO POWER SPECIFICATIONS Amplifier section FM tuner section Specifications AM tuner section Video section General Glossary Press and light Press or to select Turn jog dial to select See page Settings Using SUR, LEVEL, BASS/TREBLE, and SET UP buttons Remote Button Description (STR-DE445 only) Remote Button Operations Function Changing the factory setting of a function button Remote Button Description (STR-DE445 only) 1 2 Index A B C D