Manuals / Brands / Home Audio / Stereo Receiver / Sony / Home Audio / Stereo Receiver

Sony STR-DE698 Programming the remote, Selecting the command mode of the remote, 50GB, Selecting the command mode, To check the command mode of the remote

1 64

Download 64 pages, 2.3 Mb

Selecting the command mode of the remote

Set the remote command mode using the

RM SET UP button and the remote command mode buttons.

Selecting the command mode

You can switch the command mode (AV1 and AV2) of the remote. If the command mode of the receiver and the remote is different, you cannot use the remote to operate the receiver. To change the command mode of the receiver, see page 57.

Press AV1 (or AV2) while holding down

RM SET UP.

The indicator flashes once (twice for AV2) , then the command mode switches.

To check the command mode of the remote

Press RM SET UP. You can check the remote by the indicator.

Mode	Indicator flashes

AV1once

AV2twice

To reset the remote to factory settings

Press ?/1, AV ?/1 and MASTER VOL – at the same time.

The indicator flashes 3 times, then goes off.

Programming the remote

You can program the remote to control non- Sony components by changing the code. Once the control signals have been memorized, you can use those components as part of your system.

Furthermore, you can also program the remote for Sony components that the remote is unable to control. Note that the remote can only control components that accept infrared wireless control signals.

1 Press AV ?/1 while holding down

RM SET UP.

The indicator lights up.

2 Press the input button (including TV ?/1) for the component you want to control.

For example, if you are going to control a CD player, press SA-CD/CD.

3 Press the numeric buttons to enter the numeric code (or one of the codes if more than one code exists) corresponding to the component and the maker of the component you want to control.

See the tables on pages 51–53 for information on the numeric code(s) corresponding to the component and the maker of the component (the first digit and the last two digits of the numeric code correspond to the category and the maker’s code respectively).

4 Press ENTER.

Once the numeric code has been verified, the indicator slowly flashes twice and the remote automatically exits the programming mode.

5 Repeat steps 1 to 4 to control other components.

50GB

Contents

Page WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture About This Manual Note for the supplied remote Table of Contents 1: Check how to hookup your components Required cords AAudio cord BAudio/video cord CVideo cord DS-videocord 1a: Connecting components with digital audio output jacks 2 Connect the video jacks Hooking up an MD/Tape deck or a Super Audio CD/CD player 1b: Connecting components with multi channel output jacks 11GB 1c: Connecting components with only analog audio jacks Hooking up video components 13GB 2: Connecting the antennas 3: Connecting speakers Required cords A Speaker cords (not supplied) B Monaural audio cord (not supplied) SPEAKERS FRONT B 4:Connecting the AC power cord 5: Setting up the speakers xSP. PAT. X –X(Speaker setup pattern) x SWS.W. XXX (Sub woofer selection) x L R XXXXX (Front speakers size) x C XXXXX (Center speaker size) x SLSRXXXXX (Surround speakers size) x SBLSBR/SBXXXXXX (Surround back speaker selection) x L R DIST. X.X m (XX ft.) (Front speaker distance) x C DIST. X.X m (XX ft.) (Center speaker distance) 20GB x SLSRDIST. X.X m (XX ft.) (Surround speaker distance) x SBLSBR/SBDIST. X.X m (XX ft.) (Surround back speaker distance) x SLSRXXXX/XX (Surround speaker position) 21GB 6:Adjusting the speaker levels and balance —TEST TONE Selecting the component Listening to multi channel sound — MULTI CH IN Listening to FM/AM radio Storing FM stations automatically — AUTOBETICAL Presetting radio stations Using the Radio Data System (RDS) Changing the display About the indications in the display L C R SL SR 30GB Using only the front speakers Enjoying higher fidelity sound — AUTO FORMAT DIRECT Decoding the input audio signal automatically Press A.F.D. repeatedly to select “A.F.D. AUTO” Enjoying stereo sound in multi channel (2 channel decoding mode) Press A.F.D. repeatedly to select the 2 channel decoding mode xDOLBY PL (PRO LOGIC) Selecting a sound field Selecting a sound field for music Press MUSIC repeatedly to select the sound field you want xHALL xJAZZ (JAZZ CLUB) xCONCERT (LIVE CONCERT) — SURR BACK DECODING How to select the surround back decoding mode When you select “SB AUTO” When you select “SB ON” When you select “SB OFF” 36GB Switching the audio input mode for digital components — INPUT MODE Customizing sound fields Adjusting the equalizer Advanced settings xCOL. XXXX (Color system) (Models of area code E2/E3, AR only) xDUAL (Digital broadcast language selection) xCOMP. V. A Naming preset stations and inputs Using the Sleep Timer Selecting the speaker system Recording Before you use your remote Remote button description 46GB the 47GB 48GB 49GB Selecting the command mode of the remote Programming the remote To cancel programming To activate the input after programming If programming is unsuccessful, check the following: To clear the memory of the remote The numeric codes corresponding to the component and the maker of the component To control a DAT deck To control an MD deck To control a tape deck To control an LD player To control a video CD player To control a TV To control a satellite tuner or cable box To control a tuner To control a hard disc recorder To control a blu-raydisc recorder Precautions Troubleshooting The surround effect cannot be obtained Dolby Digital or DTS multi channel sound is not reproduced Recording cannot be done The FM reception is poor Radio stations cannot be tuned in Remote control The remote does not function Error messages DEC. EROR PROTECT Specifications 59GB FM tuner section AM tuner section Video section General Supplied accessories List of button locations and reference pages Index