Sony STRDH520 4, 5, 6, Playback, 1, 2 3

36GB

D:\NORM'S JOB\SONY HA\SO0109\STR-DH520\4263361111_GB\GB05BAS_STR-DH520-

U2.fm

masterpage: Left

STR-DH520

4-263-361-11(1)

4Press V/v repeatedly to select

“AUTO xxx*”.

The test tone is output from each speaker

in sequence.

*xxx represent a speaker channel.

Note

Depending on the speaker pattern settings, test

tone may not be output from all speakers even

though you selected “AUTO xxx”.

5Adjust the speaker levels.

Use the LEVEL menu (page 54) to adjust

the speakers to have the same sounding

test tone level for each speaker.

Tips

•

To adjust the level of all speakers at the same

time, press MASTER VOL +/– or

2

+/–. You

can also use MASTER VOLUME on the

receiver.

• The adjusted value are shown on the display

panel during adjustment.

6Exit test tone.

Press any input buttons or select “OFF”

under step 4.

When a test tone is not output

from the speakers

• The speaker cords may not be connected

securely.

• The speaker cords may have the short-circuit

problem.

When a test tone is output from

a different speaker than the

speaker indicator showed in the

display panel

The speaker pattern set up is incorrect. Make

sure that the speaker connections and the

pattern match correctly.

Playback

1Turn on the connected

equipment.

2Turn on the receiver.

3Press the input button which

corresponds to the equipment

you want.

You can also use INPUT SELECTOR on

the receiver.

The selected input appears on the display

panel.

Note

When you press TUNER, “FM TUNER” or

“AM TUNER” appears for a while, and then

frequency appears on the display panel.

Basic Operations

Input

buttons

,

V/v/B/b

AMP

MENU

MASTER

VOL +/–/

2 +/–

MUTING/ SOUND

FIELD +/–

Contents

Main To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. For customers in the United States WARNING Owners Record Important Safety Instructions CAUTION For customers in Europe For customers in Australia About This Manual On Copyrights Table of Contents Connections Preparing the Receiver Basic Operations Tuner Operations Supplied accessories Inserting batteries into the remote control Description and location of parts Front panel Indicators on the display panel qsqd qa 1324 56897 q; Page Rear panel 45 1 1 1, 2 3 2 AAudio signal section Remote control To use the buttons printed in pink To control the receiver To control a Sony TV / Page To control other Sony equipment Be sure to hold down SHIFT (O) to activate the buttons printed in pink (page 12). Getting started 1: Installing the speakers Example of speaker system configuration 5.1 channel speaker system 7.1 channel speaker system using surround back speakers 7.1 channel speaker system using front high speakers Tips 2: Connecting the speakers Page 3: Connecting the TV 4a: Connecting the video equipment Using HDMI connection HDMI features Notes on HDMI connections When connecting cords If you want to connect several digital equipment, but cannot find an unused input Connecting a Blu-ray Disc player, DVD player Connections AHDMI cable (not supplied) Sony recommends that you use an HDMI- authorized cable or Sony HDMI cable. Connecting a PlayStation 3 A Connecting a satellite tuner, cable TV tuner Connecting a VCR, DVD recorder 4b: Connecting the audio equipment Tip B 5: Connecting the antennas (aerials) Before connecting antennas (aerials), be sure to disconnect the AC power cord (mains lead). 6: Connecting the AC power cord (mains lead) Initializing the receiver 1 receiver. 2 Selecting the speaker pattern 2 SPKR, then press or b. 3 PATTERN, then press or b. Using AUTO CALIBRATION (Europe, Australia and Taiwan models only) 1 (page 30). 2 3 microphone. Confirm active subwoofer setup Hold down SHIFT, then press AUTO CAL. 2: Performing Auto Calibration 1 result. 2 3 4 Checking the warning message 2 3 4 5 Adjusting the speaker levels 2 3 Selecting the calibration type 4 AUTO xxx*. 2 5 6 4 5 2 6 To activate the muting function To avoid damaging your speakers 1 2 Recording using the receiver 1 2 3 4 Listening to FM/AM radio 1 select the FM or AM band. 2 Using the control buttons on the receiver 1 2 3 4 If you cannot tune to a station 1 2 3 Tuning to a station directly (Direct Tuning) Changing the AM tuning scale Presetting FM/AM radio stations 1 2 3 4 1 Naming preset stations 2 3 4 5 Selecting the sound field 2 channel sound mode Press SOUND FIELD +/ repeatedly to select the sound field you want. x2CH ST. (2 Channel Stereo) xA. DIRECT (Analog Direct) Music mode xHP 2CH (Headphones 2CH) xHP DIR (Headphones Direct) If you connect a subwoofer Notes on sound fields Digital audio formats supported by the receiver Resetting sound fields to the default settings BRAVIA Sync Features 1 receiver. 2 Preparing for the BRAVIA Sync If your TV is compatible with the Control for HDMI-Easy Setting function 1 2 3 If your TV is not compatible with the Control for HDMI-Easy Setting function Playing back equipment with one-touch operation (One-Touch Play) Enjoying the TV sound from the speakers connected to the receiver (System Audio Control) Turning off the receiver with the TV (System Power-Off) Hold down TV, then press TV ?/1. Enjoying movies with the optimum sound field (Theater/Theatre Mode Sync) Switching between digital and analog audio (INPUT MODE) 1 input source. 2 3 A. ASSIGN, V. ASSIGN or H. ASSIGN, then press or b. 4 the following setting, then press or b. 5 Using the setting menu 2 3 4 To return to the previous display Overview of the menus Advanced Operations Page xT. TONE xFL LVL, FR LVL, CNT LVL, SL LVL, SR LVL, SB LVL, SBL LVL, SBR LVL, LH LVL, RH LVL, SW LVL xD. RANGE xPAT TE RN SURROUND menu xFRT CRS., CNT CRS., SUR CRS., FH CRS. xEFFECT xBASS xTREBLE xFM MODE xNAME IN xA/V SYNC HDMI menu SYSTEM menu xNAME IN Reassigning the input button 1 button of which you want to change the assignment, hold down AV ?/1. 2 release the input button. 3 press the corresponding button for the category you want, then release AV ?/1. Resetting the input buttons 1 VOL /2 , press ?/1 and INPUT/ . Precautions On safety On power sources On heat buildup On placement Troubleshooting Power Sound Page Image Tuner Remote control Other Error messages Clearing the memory Additional Information Specifications AUDIO POWER SPECIFICATIONS FM tuner section AM tuner section Video section General Design and specifications are subject to change without notice. Halogenated flame retardants are not used in the certain printed wiring boards. Index