Soundolier CP700 specifications Architect & Engineer Specifications

SPECIFICATIONS

DIRECT POWER OUTPUTS		PROTECTION CIRCUITS
Max Average Power @ 35Hz-20kHz with 0.1% THD		Output Offset Voltage Protection
(10-80k Filter)		Heat Sink Overheat Protection
8 Ohm, 30Hz-20KHz, 0.1% THD	240W x 2	Transformer Overheat Protection
8 Ohm, 1kHz, 0.1% THD	300W X 2	Load Shorting Protection
4 Ohm, 1kHz, 0.1% THD	400W X 2	Soft Clip Limiters
2 Ohm, 1kHz, 0.1% THD	550W X 2
Bridged Mono 8 Ohm	850W
1kHz, 1% THD
Bridged Mono 4 Ohm	1100W
1kHz, 1% THD
TRANSFORMER OUTPUTS		CONTROLS
25V	280W X 2	Power Switch, Ch 1/Ch 2 gain (41 step)
70V	350W X 2	Parallel/Stereo/Bridge Switch
100V	350W X 2
140V Bridged	700W
200V Bridged	700W
FREQUENCY RESPONSE		COOLING
Direct Outputs (+0/-3dB)	30Hz-50kHz	Dual Speed Fan, Temperature Controlled
Transformer Outputs (+0/-3dB)	30Hz-16kHz
THD+N		INDICATORS
8 Ohm, 1kHz, 240W per channel	<.05%	Power, Protect, Signal, Limit
SENSITIVITY		DIMENSIONS
Rated Ouput into 8 Ohms	1.25V	132mm X 480mm X 428mm (5.19" X 18.9" X 16.85")
VOLTAGE GAIN		NET WEIGHT
32dB		24.3kg (54 lbs)
INPUT IMPEDANCE		SHIPPING WEIGHT
Balanced/Unbalanced	20k/10k Ohm	26kg (57 lbs)
DAMPING FACTOR
8 Ohms Output, 10 Vrms	>200dB
S/N RATIO
8 Ohms per Channel @ 240W	100dB

ARCHITECT & ENGINEER SPECIFICATIONS

The amplifier shall be Atlas Sound CP700 Commercial Audio Amplifier. The power amplifier shall have two channels. At 8 Ohms, 30Hz- 20kHz, it shall deliver 240 Watts per channel. At 4 Ohms, 1kHz, it shall deliver 400 Watts per channel. At 2 Ohms, 1kHz, it shall deliver 550 Watts per channel. In bridge mono mode, with an 8 Ohm load, it shall deliver 850 Watts. In bridge mono mode, with a 4 Ohm load, it shall deliver 1100 Watts. The amplifier shall have internal circuits to protect itself from output short circuits and thermal overload and will protect attached loudspeakers from amplifier failure and DC voltages.

A variable speed fan shall provide heat sink cooling. Each channel to have an input sensitivity of 1.25V, frequency response shall be 30Hz- 50kHz +0/-3dB direct mode and 30Hz-16kHz +0/-3dB in transformer mode. Front panel indicators to include signal present, limiter, and protection LEDs. Rear mounted stepped attenuators to provide repeatability of gain settings. Input terminations shall be balanced on barrier strip terminals or XLR female connectors. Loudspeaker outputs shall be of the barrier strip type. A switch on the rear panel to provide selection of Stereo, Parallel, and Bridge Modes of operation. Dimensions shall be 5.19" X 18.9" X 16.85" and the amplifier shall weigh 57 lbs.

Specifications subject to change without notice

1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.	AtlasSound.com
TELEPHONE: (800) 876-3333 /FAX (800) 765-3435

© 2005 Atlas Sound LP Printed in U.S.A. 001105 ATS002228 RevA 11/05 SL9-2076