Soundstream Technologies Granite 60.2, Granite 180.6 Amplifier LOCATiON and Mounting, 22mH

	2	Ohms	4 Ohms		8 Ohms
mEQ	Ll	C l	Ll	C l	Ll	C l
8 0 H z	5.5mH	68Oj.lF	IlmH	33OpF	22mH	18O)lF
IOOHz	4.7mH	56OpF	9.lmH	27OpF	1 8 m H	15OpF
130Hz	3.3mH	4OOcF	6.8mH	2OOpF	15mH	1OObF
200Hz	2.2mH	3OOpF	4.7mH	15OpF	9.lmH	75pF
260Hz	1.8mH	2OOpF	3.6mH	1OOpF	6.8mH	5OpF
400Hz	l . l m H	15OpF	2.2mH	68pF	4.7mH	33pF
6 0 0 H z	0.75mH	1oopF	1.5mH	47~F	3.0mH	26pF
8 0 0 H z	0.5mH	68pF	l . O m H	33lF	2.0mH	15pF
IOOOHz	0.47mH	5OpF	0.9lmH	27pF	1.8mH	13~F
1200Hz.	0.33mH	44pF	0.75mH	22pF	1.5mH	IlpF
1800Hz	0.27mH	3OpF	0.50mH	15pF	l . O m H	6.8pF
4000Hz	O . l O m H	15pF	0.22mH	6.8pF	0.47mH	3.3pF

AMPLIFIER LOCATiON AND MOUNTING

Soundstream Granite amplifiers employ highly efficient circuitry and a unique ChassisinkTM design to maintain lower operating temperatures. When mounting the amplifier, it should be securely attached to either a panel or to an amp board or rack that is securely fastened to the vehicle, away from moisture, stray or moving objects, and major electrical components (electrical motors, fuel pumps, etc.). To provide adequate ventilation, mount the amplifier so that there are at least two inches of freelycirculating air above and to the sides of it.

A. Using the amplifier as a template, mark the mounting surface. B. Remove the amplifier and drill the holes.

C. Mount the amplifier to the surface using the provided hardware.

WIRING

You will need the following tools for the wiring of the amplifier: Phillips or slotted screwdriver, wire strippers and wire crimpers.

When baring wires for connection to the amplifier, remove 3/8” to l/2” of the insulation. For the speaker leads, use the supplied l/4” insulated female crimp connectors and slide the connector onto the terminal on the amplifier. On the power, ground and remote connections, loosen the screws on the terminal block, slide the bared wire into the connector-and tighten the screw. Determine from the chart below the minimum gauge power and ground wire required. Be sure to fuse the amplifier positive power lead within 18” of the battery.

Amplifier up to 5’ up to 70’ up to 75’ up to 20’

Granite 60.2 12 ga or larger 12 ga or larger 10 ga or larger 10 ga or larger

Granite 120.4 12 ga or larger 12 ga or larger 10 ga or larger 10 ga or larger

Granite 160.6 10 ga or larger 8 ga or larger 8 ga or larger 8 ga or larger

A. Carefully run the audio and remote turn-on cabIss to the amplifier.

B. Connect the speakers as shown in “Speaker Wiring Configurations.” Use at

1 7