Figure #2

OWNER’S MANUAL

SpeakerCraft®

AB-S

In-Wall A/B Switch

If you do not understand any part of these instructions, please contact your SpeakerCraft dealer. Improper wir- ing could cause damage to your audio system.

In-Wall Selector

The SpeakerCraft AB-S is an in-wall speaker/amplifier selector. The selector provides the ability to select between two pairs of speakers that are connected to the same amplifier or between two amplifiers that are connected to the same speaker pair.

Selector Placement

When deciding where the selector will be mounted in the wall, consider various ways it will be used. The pri- mary listening area and the ease of running the wire to your chosen location are the important things to keep in mind. The most common locations to mount selectors are by the door as you walk into the room, next to your bedside, or in the area that you will be listening to music.

Do not put the selector into the same box as a 110VAC circuit. (i.e. light switch, electrical outlet, etc.) Speaker wires can act as an "antenna" for electrical noise. Locating speaker wires too close to a light switch or dimmer may cause a buzzing or popping sound to be heard through the speakers. If you must locate the AB-S near electrical devices, use a separate electrical box.

Once a location has been chosen, you may install the selector by using a standard single gang plaster ring, or a single gang electrical box (light switch type).

Wiring the AB-S

(See Figure #1)

Caution: Please make sure your amplifier or receiver is off before proceeding.

The AB-S features SpeakerCraft's simple connect system. This system is quicker and more secure than other methods and eliminates the need for turning small screws.

For best results strip all wire no more than 1⁄4" from the end. Push the wire completely into the opening on the connec- tor then depress the lever using your finger or screwdriver. This will secure the wire (see Figure #1‑). If you need to

remove the wire simply lift the lever. This can be done with

your finger, but may be easier to use a screwdriver or similarFigure #1 tool. With the lever lifted, pull the wire out.

Use the following directions when using the selector to choose between 2 pairs of speakers con- nected to one amplifier.

(Figure #2)

1.Connect the Amplifier: Connect the amplifier's or receiver's speaker outputs to the connector labeled "ampli- fier", please observe proper channel and polarity of the connections (+ from the ampli- fier to + input on the control, left channel out to the "L" side of the connector marked "amplifier" on the selector).

2.Connect the Speakers: Connect the wires from one pair of speakers to one of the

two terminals labeled "Speak- ers". Connect the wires from the other pair of speakers to

the remaining terminal labeled "Speakers", please observe proper channel and polarity of the connections (+ from the speaker to + input on the control, left channel from the speaker to the "L" side of the connector marked "speaker" on the selector).

Use the following directions when using the switch to choose between 2 amplifiers and one pair of speakers. (Figure #3)

Page 1 Page 2
Page 1
Image 1
SpeakerCraft owner manual Ab-S, In-Wall A/B Switch, In-Wall Selector, Selector Placement, Wiring the AB-S
Page 1 Page 2

Switch specifications

The SpeakerCraft Switch is an innovative solution for managing audio and video signals in multi-room audio systems, providing a sophisticated yet user-friendly experience for both installers and end-users. This versatile switch allows you to effortlessly route different audio and video sources to various destinations throughout a home or commercial space.

One of the main features of the SpeakerCraft Switch is its ability to support multiple audio formats and video resolutions, making it compatible with a wide range of devices. Whether you are using traditional stereo audio systems, surround sound setups, or modern streaming devices, the Switch can accommodate all, providing seamless integration with your existing systems.

The technology behind the SpeakerCraft Switch includes advanced digital processing capabilities, which allow for signal enhancement and optimal quality. This ensures that every audio and video signal is transmitted with the highest fidelity, yielding an immersive experience that is crucial for home theaters, music rooms, and entertainment venues.

Additionally, the SpeakerCraft Switch incorporates a user-friendly interface that simplifies operation for both installers and users. With intuitive controls, users can easily select their desired source and destination without any technical hassle. This ease of use extends to the installation process as well; the device is designed for straightforward integration into existing setups, reducing the time and effort needed for installation.

Another characteristic of the SpeakerCraft Switch is its robust build quality, ensuring reliability and durability over time. This is crucial for installations in both residential and commercial environments where usage might demand higher durability standards.

The multi-zone capability of the SpeakerCraft Switch allows for different audio and video content to be played simultaneously in various rooms, catering to diverse tastes and preferences within a household or commercial setting. This flexibility is complemented by a range of connectivity options, enabling compatibility with various smart home systems and control platforms for enhanced automation and ease of use.

In conclusion, the SpeakerCraft Switch stands out as a premium choice for those looking to manage audio and video seamlessly across multiple zones. Its sophisticated technology, compatibility with various devices, user-friendly design, and high-quality construction make it a valuable asset for any integrated audio and video installation. Whether for home use or professional applications, the SpeakerCraft Switch delivers performance and flexibility that meets modern entertainment needs.
Top Page Image Contents