Spectra HL700 warranty Battery Status Specifications, Move clamp position, Rod Clamp, Warranty

Battery Status				Specifications
				Working Radius:	1 m - 460 m (3 ft - 1500 ft)
				(Laser dependent):
				Laser Detection Height:	127 mm	(5“)
Full -				Numeric Readout Height:	102 mm	(4“)
	Half -	Outline -	Flashing -	Accuracy (Dead band):
Batteries OK	Initial	Approx.	Change	Ultra Fine	0.5 mm	0.02 in	1/32 in
	Warning	30 Minutes	Batteries	Super Fine	1.0 mm	0.05 in	1/16 in
		Remaining		Fine	2.0 mm	0.10 in	1/8 in
				Medium	5.0 mm	0.20 in	1/4 in
Move clamp position
				Coarse	10.0 mm	0.50 in	1/2 in
	Center on-grade clamp position - clamp			Calibration	0.1 mm	0.01 in	1/64 in
				Reception Angle:	± 45° minimum
	position is sensed automatically and			Detectable Spectrum:	610 nm ... 780 nm
	displayed. Standard center position displays			Beeper Volumes:	Loud = 110 dBA
	an equal amount of information above				Medium = 95 dBA
	and below grade. With no clamp, center				Low = 65 dBA
	on-grade.			LED Grade Indicators:	Front, Green on-grade,
					Red Hi/Low
	Offset on-grade clamp position - clamp			Power Supply:	2 x 1.5 Volt “AA” batteries
	position is sensed automatically and			Battery Life:	60+ hours
	displayed. Offset clamp position moves			Automatic Shut Off:	Selectable, 30 min, 24 h, Off
	the on-grade location to allow more grade			Environmental:	Waterproof, Dustproof to IP67
	information to be displayed above grade.			Weight without clamp:	371 g (13.1 oz.)
				Dimensions without
	This is useful in applications where going
				clamp:	168 x 76 x 36 mm
	below grade is not required, i.e. driving
					(6.6” x 3.0” x 1.4”)
	stakes down to grade.
				Operating Temperature:	-20°C...+60°C (-4°F... +140°F)
				Storage Temperature:	-40°C...+70°C (-40°F...+158°F)
Rod Clamp				*Specifications subject to change without notice.
			6	Warranty

HL700 Laserometer

User Guide

www.trimble.com

EMC Declaration of Conformity

This receiver has been tested and found to comply with the limits for a Class B digital device for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Com- munication, and is pursuant to part 15 of the Federal Communication Commission (FCC) rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This receiver generates radio frequency. If it’s not used in accordance with the instructions, it may cause harmful interference to radio or televi- sion reception. Such interference can be determined by turning the re- ceiver off and on. You are encouraged to try eliminating the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the laser and the receiver. For more information, consult your dealer or an experience radio/television technician.

CAUTION: Changes or modifications to the receiver that are not ex- pressly approved by Trimble could void authority to use the equipment.

Declaration of Conformity

Application of Council Directive(s):	89/336/EEC
Manufacturer’s Name:	Trimble Navigation Ltd.
Manufacturer’s Address:	5475 Kellenburger Road
	Dayton, Ohio 45424-1099 U.S.A.
European Representative Address:	Trimble GmbH Am Prime Parc 11
	65479 Raunheim, Germany
Model Number:	HL700
Conformance to Directive(s):	EC Directive 89/336/EEC using
	EN55022 and EN50082-1
Equipment Type/Environment:	ITE/residential, commercial
	& light industrial
Product Standards:	Product meets the limit B and
	methods of EN55022
	Product meets the levels and
	methods of IEC 801-2, 8 kV air,
	4 kV contact IEC 801-3, 3 V/m
	26 to 1000 MHz 80%, @ 1 kHz

1

2

5

4

3

Trimble warrants the HL700 to be free of defects in material and work- manship for a period of three years. Trimble or its authorized service center will repair or replace, at its option, any defective part, or the entire product, for which notice has been given during the warranty period. If required, travel and per diem expenses to and from the place where repairs are made will be charged to the customer at the prevailing rates. Customers should send the product to Trimble Navigation Ltd. or the

4

35

6

7

2 8

1314

12

11

1015

1.Captive Rod Clamp Screw - attaches to the back of detector.

2.Alignment Points (2) - help secure and align rod clamp.

3.Clamping Screw Knob - secures clamp to rods by moving the traveling jaw. Clockwise tightens; Counterclockwise loosens.

4.Reference Bar - top of bar is aligned with on-grade.

5.Traveling Jaw - moving jaw grips tightly to rods.

6.Reversible Face - slanted face for round and oval rods; flat face for rectangular and square rods.

Notice to Our European Union Customers

For product recycling instructions and more information, please go to: www.trimble.com/environment/summary.html

Recycling in Europe

nearest authorized service center for warranty repairs or exchange, freight prepaid. Any evidence of negligent, abnormal use, accident, or any attempt to repair the product by other than factory-authorized personnel using Trimble certified or recommended parts, automatically voids the warranty. The foregoing states the entire liability of Trimble regarding the purchase and use of its equipment. Trimble will not be held responsible for any consequential loss or damage of any kind. This warranty is in lieu of all other warranties, except as set forth above, including any implied warranty merchantability of fitness for a particular purpose, are hereby disclaimed. This warranty is in lieu of all other warranties, expressed or implied.

1

Front view

1.Keypad - Power, Accuracy, Units & Volume switches.

2.LED-Display - Green for on-grade & Red for high / low

3.Beeper output - Fast, solid & slow audible signal.

4.Bubble Vial - aids in keeping HR700 level.

5.Anti-strobe sensor - Reduces false indication from strobe lights.

6.SuperCell Reception Window - 5 in / 127 mm of height.

7.Front LCD - Displays elevation, settings and status.

8.On-grade Mark - Aligned with laser center on-grade reading.

16

9

Rear view

9.Battery Door & Latch for two “AA” batteries.

10.Marking Notch (3.15 in / 80 mm from top).

11.Captive Screw Thread, Center on-grade clamp position.

12.Captive Screw Thread, Offset on-grade clamp position.

13.Clamp Guides - Dimples align rod clamp.

14.Serial Number / ID Label.

15.Rear LCD - repeats indications of front LCD.

16.Rubber over mold - Protects the unit from drops

To recycle Trimble WEEE, call: +31 497 53 2430, and

ask for the “WEEE associate,” or

Mail a request for recycling instructions to:

Trimble Europe BV c/o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel, NL

Trimble Construction Division

5475 Kellenburger Road

Dayton, Ohio 45424-1099

U.S.A.

+1-937-245-5600 Phone

www.trimble.com N324

© 2008, Trimble Navigation Limited. All rights reserved. Reorder PN 1277-3850 (05/08)

Installing the Batteries

1.Open the battery door using a coin or similar pry device to release the battery door tab.

2.Insert two AA batteries noting the plus (+) and minus (-) diagrams inside the battery housing.

3.Close the battery door. Push down until it “clicks” into the locked position.