Prepare the Collar Receiver

 

05

 

Your Collar Receiver comes with short Contact Points installed. If your dog has a long or thick coat, you have two options to

 

ensure consistent contact: either trim the hair around the Contact Points or switch to the longer Contact Points included with

 

::

your system (follow 1-5 in diagram 5A). Tighten the Contact Points with pliers one-half turn beyond finger tight. Check the

 

tightness weekly.

 

STEP

To Insert and Remove the Battery

 

Note: Do not install the battery while the Collar Receiver is on your dog.

 

1. Remove the screws with a Philips screwdriver (5B).

 

2. Remove the Battery Lid (5B).

 

3. Install a 9-volt alkaline battery (5C).

 

 

4. Replace the Battery Lid (5C). Ensure o-ring stays in place.

 

 

 

 

5. Reinstall the screws. Do not over-tighten the screws.

 

 

Replacement 9-volt alkaline batteries can be found at many retailers.

Function and Response Table

Indicator Light

Stimulation Level

Collar Receiver Function

Temperament of Dog

Response

 

 

 

 

 

 

 

 

1

Flash

1

Beep and Vibrate (No Stimulation)

 

 

 

 

 

 

2

Flashes

2

Low Stimulation

Timid

 

 

 

 

3 Flashes

3

Medium Stimulation

Timid or Average

4 Flashes

4

Medium High Stimulation

Average or Stubborn

5

Flashes

5

High Stimulation

Stubborn

 

 

 

 

Flashes once every

 

Low Battery

 

4 to 5 seconds

 

 

 

 

 

 

 

 

Note: Begin training with Stimulation Level 2 and only increase if your dog does not respond to the Stimulation.

= Beep and Vibration Only + = Beep, Vibration and Stimulation = Stimulation Only

5A

 

 

5B

 

1

2

 

 

 

 

2

 

 

 

 

3

5

4

 

 

3

 

 

 

 

 

5C

Important: The Stimulation Mode Switch (5F) can alter the response of the Collar

5F

Receiver. When this Stimulation Mode Switch is set to “ ’’ or

+

’’, the Collar

Receiver will respond according to the Function and Response Table above. However, if the

 

Stimulation Mode Switch is set to “ ’’, this setting will override the Stimulation

Stimulation

Level 1 function. In this case, no Stimulation will be delivered, and the Collar Receiver will

Mode

NOT beep or vibrate; it will only make the ticking sound that normally indicates Stimulation.

Switch

 

We recommend to leave the Stimulation Mode Switch on the

’’ or

+ ’’

Range

Switch

settings.

 

 

 

__________________________________________________

67-

A

 

To Set the Stimulation Level

Read all steps before attempting to set the

5D

Stimulation Level.

 

1.

Remove the clear plastic cover with a coin to

 

expose the Stimulation Level Button (5D).

2.

With the battery installed, press the Stimulation

 

Level Button and release when the Receiver

 

Indicator Light lights up (5E).

3.

The Receiver Indicator Light will emit a series of

 

flashes representing the Stimulation Level. For

 

example, 2 flashes = Stimulation Level 2.

5E

STEP :: 06

Set the Boundary Width and Test the Collar Receiver

The Range Switch on the side of the Fence Transmitter has two settings. Set the Range Switch to LOW if the amount of wire used for your property is less than 4,400 feet. Set the Range Switch to HI if you used between 4,400 and 8,600 feet of wire.

Use the Range Adjuster knob to set the width of the Warning Zone and Stimulation Zone

(6A). Set the Boundary Width as wide as possible to give your dog the widest Warning and Stimulation Zones without reducing the Boundary Area too much.

Note: The Range Adjuster knob does not change the Stimulation Level.

CAUTION The Receiver Collar should NOT be on your dog when the system is tested. Your dog may receive an unintended correction.

6A

4

5

6

3

 

7

28

1

9

0

10

4

5

6

3

 

7

2

 

8

1

 

9

0

 

10

4.

Increase the Stimulation Level by pressing and

 

releasing the Stimulation Level Button within 5

 

seconds of the previous series of flashes.

5.

After setting the Stimulation Level, replace the

 

cover to protect the Stimulation Level Button.

To identify the Warning and Stimulation Zones, make sure the Collar Receiver’s battery is

 

6B

properly installed, the Stimulation Level is set at 2 or above, and the Test Light contacts are

 

held to the Contact Points (6B). Walk toward the Boundary Wire holding the Collar Receiver at

 

your dog’s neck level (6C) until the Receiver Collar beeps (6D).

 

Note: The Collar Receiver is waterproof, which can make the beep hard to hear.

The Stimulation Levels increase in strength from 1 to 5. Pushing the Stimulation Level Button while the Collar Receiver is on level 5 will cause the Collar Receiver to go back to level 1. Refer to the Function and Response Table, on the following page, to choose the Stimulation Level that best fits your dog.

The Collar Receiver is equipped to automatically increase the level of Stimulation the longer your dog remains in the Stimulation Zone if the collar is set at level 2 or above.

The Receiver Indicator Light acts as a low battery indicator, flashing every 4 to 5 seconds when a replacement is required.

12

1-800-732-0144

LIGH

T

TEST

SPORTDOG.COM

13

400-1178.indd 12-13

3/5/10 4:28 PM

Page 7
Image 7
SportDOG 100A manual Prepare the Collar Receiver, Function and Response Table, To Insert and Remove the Battery

100A specifications

The SportDOG 100A is a state-of-the-art electronic collar designed for training dogs, particularly hunting and sporting breeds. This device is engineered to deliver reliable performance for both novice pet owners and professional trainers, making it one of the most sought-after tools in the market today.

One of the standout features of the SportDOG 100A is its impressive range. With a transmit distance of up to 1000 yards, this collar allows trainers to maintain control and communication with their dogs even from a significant distance. This is particularly beneficial during field training sessions or hunting expeditions, where the dog may be far from the handler.

The SportDOG 100A incorporates 7 levels of stimulation, allowing users to tailor the intensity of the correction to suit their dog’s temperament and training needs. This gradual approach to stimulation can reinforce positive behaviors and discourage unwanted actions without causing excessive stress to the animal. Additionally, the collar features a tone and vibration mode, providing alternative training options that cater to different learning styles.

Durability is another critical characteristic of the SportDOG 100A. This collar is waterproof and submersible, making it suitable for use in various weather conditions. Whether it's a rainy day or a dive into a lake, the SportDOG 100A continues to function flawlessly, showcasing its rugged build quality designed specifically for outdoor use.

The collar is powered by a rechargeable lithium-ion battery, which offers a robust runtime. Users can expect up to 70 hours of continuous use on a single charge, ensuring that the collar is ready for training sessions without frequent interruptions. The battery indicator helps users keep track of charge levels, eliminating the guesswork associated with battery life.

Moreover, the SportDOG 100A showcases a sleek and ergonomic design that ensures comfort for the dog during extended wear. The adjustable strap accommodates various neck sizes, securing a snug fit to prevent slippage while maintaining the dog’s comfort.

Overall, the SportDOG 100A stands out in the realm of dog training collars with its impressive range, customizable stimulation options, durability, and user-friendly features. This collar is an ideal choice for anyone looking to enhance their dog's training experience while ensuring their safety and comfort. Whether used in professional training or casual outings, the SportDOG 100A proves to be a reliable companion for both dogs and handlers alike.